Доступно к заказу
Цена по запросу
И выбери подходящего.
Description
- High load capacity in all load directions, including moments about all axes, due to the use of largest possible ball sizes.
- Size 15 and up with a lube nipples on the end face and relubrication port on the side
- Low friction
- All steel parts of the runner block are made of corrosion-resistant, martensitic steel.
- The runner blocks are delivered on a mounting aid.
Features
- Accuracy classes P, H and N
- Relubrication hole available
- Smooth, quiet running thanks to optimally designed ball return and guidance
- Ball retention for easy replacement
Product description
| 1) | Sizes 9/M3, 12 |
| 2) | Size 15 |
Technical data
Load capacities and load moments
| Size | 9/M3 | 12 | 15 | ||
| C 1) | N |  | 2825 | 4340 | 7460 |
| C0 1) | N | 5590 | 8250 | 14085 | |
| Mt 2) | Nm |  | 23.5 | 51.4 | 151 |
| Mt0 2) | Nm | 46.4 | 97.7 | 285.2 | |
| ML 2) | Nm |  | 15.8 | 28.7 | 66.1 |
| ML0 2) | Nm | 31.2 | 54.6 | 125 | |
| 1) | Calculated values as per DIN 636, Part 2 |
| 2) | Calculated values (derived from C, C0) |
General technical data
| Size | 9/M3 | 12 | 15 | |
| amax 1) | m/s² | 250 | ||
| vmax 2) | m/s | 3 | ||
| m | g | 41 | 76 | 170 |
| Material | NR II | |||
| Operating conditions | ||||
| Size | 9/M3 | 12 | 15 | |
| Permissible ambient temperature (min ... max) 3) | -10 °C ... +80 °C | |||
| 1) | Only with pre-tensioned systems. For non-pre-tensioned systems: amax = 50 m/s2 |
| 2) | Speeds of up to 5 m/s are possible. Service life is limited by increased wear to plastic parts. |
| 3) | Brief peaks up to 100°C are permissible. |
Note on dynamic load capacities and moments (see the table)
Determination of the dynamic load ratings and moments is based on a total travel of 100,000 m.
Often only 50,000 m are actually stipulated. For comparison: Multiply values C, Mt and ML from the table by 1.26.
Observe friction of the different seals. See document “Technical data”.
Technical data
Accuracy classes
Legend
| Symbol | Description | Unit |
| amax | Maximum acceleration travel | m/s2 |
| C | Dynamic load capacity | N |
| C0 | Static load capacity | N |
| m | Mass | g |
| ML | Dynamic longitudinal moment load capacity | Nm |
| ML0 | Static longitudinal moment load capacity | Nm |
| Mt | Dynamic torsional moment load capacity | Nm |
| Mt0 | Static torsional moment laod capacity | Nm |
| vmax | Maximum permissible speed | m/s |
Diagrams/characteristic curves
Rigidity of the miniature ball rail systems at pretension
Mounted runner block with 4 screws, strength class 12.9
lift-off load
Down load
Dimensions
| 1) | Funnel-type lube nipple |
| 2) | 4 lubrication holes |
| 3) | Size 15 |
| 4) | Sizes 9/M3, 12 |
Dimensions
| Size | 9/M3 | 12 | 15 | |
| A | mm | 30 | 40 | 60 |
| A2 | mm | 18 | 24 | 42 |
| A3 | mm | 6 | 8 | 9 |
| B | mm | 51 | 59.5 | 74.5 |
| B1 | mm | 38 | 45 | 57.6 |
| B2 | mm | - | 77.5 | |
| E1 | mm | 23 | 28 | 45 |
| E2 | mm | 24 | 28 | 35 |
| H | mm | 12 | 14 | 16 |
| H1 Without longitudinal seal | mm | 9 | 10 | 12 |
| H1 With longitudinal seal | mm | 9.65 | 10.65 | 12.65 |
| K | mm | - | 4 | |
| N3 | mm | 3.2 | 4 | 4.5 |
| N5 | mm | - | 2.1 | |
| S2 | mm | M3 | M4 | |
| V1 | mm | 2.8 | 3.3 | 4.7 |
Project planning information
General technical data and calculation
Mounting
General mounting instructions
Maintenance
Start-up and maintenance
Delivery notes
load errorDownloads
 | Profiled rail systems Manual | R320103885_EN | 2016-09-01 | English | PDF | 11.5MB Product Groups: Linear guides |
| Miniature Ball Rail Systems Catalog | R999001207 | 2021-08-01 | English | PDF | 4.8MB Product Groups: Miniature Ball Rail Systems only PDF version available |
Нет отзывов об этом товаре.