Артикул: RX8482
В наличии
Linear Sets with Super Linear Bushings H, with side opening, adjustable, R1706 LSAHSE-H-..-VD
Цена по запросу Стоимость зависит от выбранного способа оплаты и количества товара.
Не отвечаем 5 минут — скидка на весь заказ!
Нужна скидка? Звони — сделаем лучшее предложение
Работаем по всей России
Возможны самовывоз и доставка по всей территории России
Надежность
Профессиональная поддержка
Description
- Precision housing (aluminum)
- Super Linear Bushing H
- Compensate for misalignments of up to 30 ft
- Fully sealed
- Secured with bolt
Features
- Relubricatable
Technical data
General technical data
| Ø d | mm | 20 | 25 | 30 | 40 | 50 |
| amax | m/s² | 150 | ||||
| vmax | m/s | 5 | ||||
| m | kg | 0.35 | 0.7 | 1.03 | 1.8 | 3 |
| FR 1) | N | 4 | 4.5 | 6 | 7.5 | 9 |
| Breakaway force | N | 7.5 | 10.5 | 13.5 | 18 | 22.5 |
| Radial clearance | Comes clamped to h5 shaft (lower limit) and set to zero clearance | |||||
| Operating conditions | ||||||
| Permissible ambient temperature (min ... max) | -20 °C ... +80 °C | |||||
| 1) | Frictional drags generated by Linear Bushings with integrated wiper seals on two sides when not under radial load. The frictional drags depend on speed and lubrication. |
Load capacities and load moments
| Ød | mm | 20 | 25 | 30 | 40 | 50 |
| C 1) | N | 2520 | 4430 | 6300 | 9680 | 16000 |
| C0 1) | N | 1880 | 3360 | 5230 | 7600 | 12200 |
| 1) | The load ratings apply for the main direction of loading. |
| The load ratings are based on a total travel of 100, 00 m. When based on 50 000 m, the values in the table need to be multiplied by 1.26. |
Legend
| Symbol | Description | Unit |
| Ød | Shaft diameters | mm |
| amax | Maximum acceleration travel | m/s2 |
| C | Dynamic load capacity | N |
| C0 | Static load capacity | N |
| FR | Friction force | N |
| m | Mass | kg |
| vmax | Maximum permissible speed | m/s |
See "Technical data – Load direction factors" and the diagrams/characteristic curves section for exact values for the 4 main directions of loading.
Refer to the "Load direction factor" diagrams for load in the direction of opening.
Effect of load direction on load rating
| a) | Closed |
| b) | Open |
Main direction of loading
Load direction factors
The load ratings C and C0 apply for the load direction ρ = 0°. For all other load directions, the load ratings must be multiplied by the factors fr (dynamic load rating C) or fρ0 (static load rating C0).
Load direction factor Super H
| Shaft | Load direction factor (dynamic load capacity) | |||||
| Ø d (mm) | ⇩ | ⇒⇐ | ⇑ | ⇩ | ⇒⇐ | ⇑ |
| 20 - 25 | 1 | 0,80 | 0,98 | 1 | 0,80 | 0,67 |
| 30 - 60 | 1 | 0,70 | 0,91 | 1 | 0,70 | 0,62 |
| Load direction factor (static load capacity) | ||||||
| 20 - 25 | 1 | 0,70 | 0,87 | 1 | 0,70 | 0,67 |
| 30 - 60 | 1 | 0,62 | 0,80 | 1 | 0,62 | 0,61 |
 |  | |||||
Reduced load capacity with short stroke
In case of short stroke, the service life of the shaft is less than that of the super Linear Bushing. The load ratings C specified in the tables must therefore be multiplied by the factor f.s .
| 1) | fs = factor |
| 2) | s = movement path |
Reduced load capacity with high load
The load rating is reduced under high load F. The dynamic load rating must be multiplied by the load factor f.F .
| 1) | fF = load factor |
Tolerances and guide parallelism during operation for R1706 Linear Sets and steel shaft with ready-mounted R1015 shaft support rail
| 1) | See "Tolerances" table for exact values. |
| 2) | P1, P2 = parallelism P1 and P2 |
| 3) | L = guide length |
| a) | Single or combined shaft support rails |
Tolerances and guide parallelism during operation for R1703 and R1704 Linear Sets and steel shaft with ready-mounted R1016 shaft support rail
|
| Tolerance zone of the shaft | Shaft Ød (mm) | |||||
| 20 | 25 | 30 | 40 | 50 | |||
| Tolerances (µm) 3) | H01) 4) | h6 | +20 | +20 | +20 | +20 | +20 |
| -35 | -35 | -35 | -36 | -36 | |||
| h7 | +20 | +20 | +20 | +20 | +20 | ||
| -39 | -39 | -39 | -41 | -41 | |||
| A31) | h6 | +20 | +20 | +20 | +21 | +21 | |
| -33 | -33 | -33 | -37 | -37 | |||
| h7 | +20 | +20 | +20 | +20 | +20 | ||
| -41 | -41 | -41 | -46 | -46 | |||
| Parallelism P1 2)4) | h6 | 29 | 29 | 29 | 30 | 30 | |
| h7 | 30 | 30 | 30 | 32 | 32 | ||
| Parallelism P2 2)4) | h6 | 29 | 29 | 29 | 34 | 34 | |
| h7 | 31 | 31 | 31 | 37 | 37 | ||
| 1) | Measured from center of housing. |
| 2) | With clamped and fastened guide. |
| 3) | The tolerances apply for the set with shaft and shaft support rail. |
| 4) | Single or combined shaft support rails |
Definition of dynamic load ratings
Diagrams/characteristic curves
Load direction factors
| a) | Closed |
| b) | Open |
Super Linear Bushings can be installed in any location. Choose a location that ensures that the main direction of loading is always ρ = 0°.
Dimensions
| a) | Lubricating hole M8 x 1 sealed with plastic cap |
| a) | Lubricating hole M8 x 1 sealed with plastic cap |
Dimensions
| Ød | mm | 20 | 25 | 30 | 40 | 50 |
| D | mm | 32 | 40 | 47 | 62 | 75 |
| α | ° | 54 | 55 | 60 | 52 | |
| A | mm | 60 | 75 | 86 | 110 | 127 |
| E1 | 22 mm ±0.15 | 28 mm ±0.15 | 34 mm ±0.15 | 43 mm ±0.15 | 50 mm ±0.15 | |
| E2 | 30 mm ±0.15 | 36 mm ±0.15 | 42 mm ±0.15 | 48 mm ±0.15 | 62 mm ±0.15 | |
| E3 | mm | 35 | 42 | 52 | 65 | 75 |
| E4 | mm | 35 | 45 | 52 | 60 | 75 |
| H | mm | 30 | 35 | 40 | 45 | 50 |
| Tolerance for H 1) | µm | + 8 - 16 | ||||
| H1 | mm | 60 | 72 | 82 | 100 | 115 |
| H4 | mm | 22 | 26 | 30 | 38 | 45 |
| L | mm | 47 | 59 | 69 | 81 | 101 |
| L2 | mm | 17.5 | 22 | 27 | 31 | 39 |
| M 1) | 17 mm ±0.01 | 21 mm ±0.01 | 25 mm ±0.01 | 32 mm ±0.01 | 38 mm ±0.01 | |
| N1 | mm | 42 | 50 | 55 | 67 | 78 |
| N2 | mm | 15 | 18 | 24 | 30 | |
| S | mm | 8.4 | 10.5 | 13.5 | 15.5 | 17.5 |
| S1 | M10 | M12 | M16 | M20 | ||
| S2 | mm | 6 | 8 | 10 | 12 | |
| SW | mm | 2.5 | 3 | 4 | 5 | |
| V | mm | 5 | 6.5 | 8 | 10 | 12 |
| W | mm | 9.5 | 12 | 12.8 | 16.8 | 22.1 |
| 1) | Clamped (fastened) in relation to Ø d. |
Legend
| Symbol | Description | Unit |
| Ød | Shaft diameters | mm |
| C/C0 | Main direction of loading |
Legend
| Symbol | Description | Unit |
| Ød | Shaft diameters | mm |
| C/C0 | Main direction of loading |
Project planning information
Life expectancy calculation
Mounting
General mounting instructions
Commissioning
load errorMaintenance
load errorCertification
load errorSafety Instructions
load errorDownloads
 | Linear Bushings and Shafts Manual | R320103669 | 2005-07-01 | English, French, German, Italian | PDF | 3.6MB Product Groups: Linear Bushings and Shafts |
| Linear Bushings Catalog | R999000488 | 2015-02-01 | English | PDF | 14.9MB Product Groups: Linear Bushings and Shafts |
Отзывы о товаре
Аналогичные товары
Официальный поставщик Bosch Rexroth
Продажи на территории России
Оптовые и розничные продажи
Снижение логистических расходов
Индивидуальные условия
Выгода без посредников
Единая система поставок
Весь ассортимент на складе