Артикул: RX7599
High-response directional valves, pilot operated, with electrical position feedback and integrated electronics (OBE) 4WRTE
Доступно к заказу
Цена по запросу
И выбери подходящего.
Description
- Size 10 … 35
- Component series 4X
- Maximum operating pressure 350 bar
- Maximum flow 3000 l/min
- Nominal flow 25 … 1000 l/min
Features
- Reliable - proven and robust design
- Safe
- Automatic pressure compensation in the control chambers of the main stage by the pilot controlvalve
- Control spool of the main stage in the springcentered central position and/or in the offset position
- Optionally with spool position monitoring - Flexible - suitable for position, velocity and pressure control
- Precise - high response sensitivity and little hysteresis
Product description
Type code
01 | 02 | 03 | 04 | 05 | 06 | 07 | 08 | 09 | 10 | 11 | 12 | 13 | 14 | 15 | 16 | 17 | |||
4 | WRT | E | ‒ | 4X | / | 6E | G24 | K31 | / | * |
01 | 4 main ports | 4 |
02 | High-response directional valve, pilot operated | WRT |
03 | With integrated electronics (OBE) | E |
04 | Without spool position monitoring | no code |
With spool position monitoring (NG16 … NG35 only) | M | |
05 | Size 10 | 10 |
Size 16 | 16 | |
Size 25 | 25 | |
Size 27 | 27 | |
Size 32 | 32 | |
Size 35 | 35 | |
06 | Symbols; for the possible version, see "Symbols/Circuit diagrams" | |
Rated flow (Δp = 5 bar/control edge) | ||
07 | Size 10 | |
25l/min 1) | 25 | |
50l/min 2) | 50 | |
90 l/min | 100 | |
Size 16 | ||
150l/min 3) | 150 | |
220l/min | 220 | |
Size 25 | ||
220l/min | 220 | |
350 l/min | 350 | |
Size 27 | ||
500 l/min | 500 | |
Size 32 | ||
400 l/min | 400 | |
600 l/min | 600 | |
Size 35 | ||
1000 l/min | 1000 | |
Flow characteristic | ||
08 | Linear | L |
Linear with fine control range | P | |
09 | Component series 40 … 49 (40 … 49: unchanged installation and mounting dimensions) | 4X |
Pilot control valve | ||
10 | Proportional solenoid with detachable coil (NG6) | 6E |
Power supply | ||
11 | Direct voltage 24 V | G24 |
Pilot oil flow | ||
12 | External pilot oil supply, external pilot oil return | no code |
Internal pilot oil supply, external pilot oil return | E | |
Pilot oil supply internal, pilot oil return internal | ET | |
External pilot oil supply, internal pilot oil return | T | |
Electrical connection | ||
13 | Without mating connector, connector according to DIN EN 175201-804 | K31 4) |
Electrical interface | ||
14 | Command value/actual value ±10 V | A1 |
Command value/actual value 4 … 20 mA | F1 | |
Command value/actual value ±10 V, enable signal (pin C) | A5 5) | |
Seal material | ||
15 | NBR seals | M |
FKM seals | V | |
16 | Without electronics protection membrane | no code |
With electronics protection membrane | -967 | |
17 | Further details in the plain text | * |
1) | Symbol E, W6-, W8- and V only with flow characteristic "L" |
2) | Symbol E1-, W8- and V1 only with flow characteristic "L" |
3) | Symbol V1 only with flow characteristic "L" |
4) | Mating connectors, separate order, see "Accessories" |
5) | When replacing the component series 3X by 4X, the electronics interface is to be defined with A5 (enable signal at pin C). |
Technical data
(For applications outside these values, please consult us!)
general
Type | 4WRTE | ||||||
Size | 10 | 16 | 25 | 27 | 32 | 35 | |
Component series | 4X | ||||||
Installation position | any, preferably horizontal | ||||||
Earth | kg | 8.7 | 11.2 | 16.8 | 17 | 31.5 | 34 |
Ambient temperature range | °C | -20 … +50 | |||||
Sine test according to DIN EN 60068-2-6 | 10 ... 2000 Hz / maximum 10 g / 10 cycles / 3 axes | ||||||
Noise test according to DIN EN 60068-2-64 | 20 ... 2000 Hz / 10 gRMS / 30 g peak / 30 min / 3 axes | ||||||
Transport shock according to DIN EN 60068-2-27 | 15 g / 11 ms / 3 shocks / 3 axes | ||||||
MTTFD values according to EN ISO 13849 1) | Years | 150 | |||||
Damp heat according to DIN EN 60068-2-30 | Variant 2: +25 °C … +55 °C, 90 % … 97 % relative humidity, 2 cycles á 24 hours |
1) | With symbol E, E1, W6 and W8; in longitudinal control spool direction, there is sufficient positive overlap without shock/vibration load; observe the installation orientation with regard to the main direction of acceleration. |
hydraulic
Type | 4WRTE | ||||||||
Size | 10 | 16 | 25 | 27 | 32 | 35 | |||
Maximum operating pressure | bar | 350 | 270 | 350 | |||||
Maximum operating pressure | Port P | bar | 350 | 270 | 350 | ||||
Anschluss A | bar | 350 | 270 | 350 | |||||
Port B | bar | 350 | 270 | 350 | |||||
Maximum operating pressure | Pilot control valve | Pilot oil supply 1) | bar | 25 … 315 | |||||
Maximum return flow pressure | Port T | Internal pilot oil supply | static < 10 bar | ||||||
Port T | External pilot oil supply | bar | 315 | 250 | 210 | 250 | |||
Port Y | static < 10 bar | ||||||||
Nominal flow 2) | l/min | 25 50 100 | 125 150 200 220 | 220 350 | 500 | 400 600 | 1000 | ||
Maximum flow | l/min | 170 | 460 | 870 | 1000 | 1600 | 3000 | ||
Pilot flow 3) | l/min | 7 | 14 | 20 | 27 | 29 | |||
Pilot volume 0 … 100% | cm³ | 1.1 | 2.9 | 6.8 | 17.7 | 33.9 | |||
Hydraulic fluid temperature range | °C | -20 … +80 | |||||||
preferably | °C | +40 … +80 | |||||||
Viscosity range | mm²/s | 20 … 380 | |||||||
preferably | mm²/s | 30 … 45 | |||||||
Maximum admissible degree of contamination of the hydraulic fluid, cleanliness class according to ISO 4406 (c) 4) | Class 18/16/13 according to ISO 4406 (c) | ||||||||
Hysteresis | % | ≤ 0.1 | |||||||
Response sensitivity | % | ≤ 0.05 | |||||||
Temperature drift | %/10° C | < 0.3 |
1) | For perfect system behavior, we recommend an external pilot oil supply for pressures above 210 bar. |
2) | qV nom ±10% with Δp = 5 bar/control edge; flow for deviating Δp see formula. |
3) | At port X or Y with stepped input signal from 0 to 100% (315 bar) |
4) | The cleanliness classes specified for the components must be adhered to in hydraulic systems. Effective filtration prevents faults and simultaneously increases the life cycle of the components. For the selection of the filters, see www.boschrexroth.com/filter. |

Hydraulic fluid | Classification | Suitable sealing materials | Standards | Data sheet | |
Mineral oils | HL, HLP, HLPD, HVLP, HVLPD | NBR, FKM | DIN 51524 | 90220 | |
Bio-degradable | Insoluble in water | HETG | NBR, FKM | ISO 15380 | 90221 |
HEES | FKM | ||||
Soluble in water | HEPG | FKM | ISO 15380 | ||
Flame-resistant | Water-free | HFDU, HFDR | FKM | ISO 12922 | 90222 |
Containing water | HFC (Fuchs Hydrotherm 46M, Petrofer Ultra Safe 620) | NBR | ISO 12922 | 90223 | |
Important information on hydraulic fluids:
|
electrical
Type | 4WRTE | ||
Voltage type | Direct voltage | ||
Power supply | Nominal voltage | VDC | 24 |
Lower limit value | VDC | 18 | |
Upper limit value | VDC | 35 | |
Maximum admissible residual ripple 1) | Vpp | 2.5 | |
Maximum current consumption | of the amplifier | A | 1.6 |
of the amplifier (impulse current) | A | 2.7 | |
Maximum coil temperature 2) | °C | 150 | |
Duty cycle | % | 100 | |
Maximum power consumption | 72 VA (average = 24 VA) | ||
Required fuse protection | AT | 4, time-lag | |
Protection class according to EN 60529 | IP65 (If a suitable and a correctly mounted mating connector are used.) | ||
Zero point calibration 3) | % | ≤ 1 | |
Voltage input "A1" (differential input) | Measurement range | VDC | -10 ... +10 |
Input resistance | Ω | 100 | |
Current input "F1" | Input current | mA | 4 ... 20 |
Input resistance | Ω | 100 | |
Enable input "A5" | Low level | VDC | 0 ... 2 |
High level | VDC | > 11 |
1) | Observe the absolute limit values of the supply voltage. |
2) | Due to the surface temperatures of the solenoid coils, the standards ISO 13732-1 and ISO 4413 (contact protection) must be observed. |
3) | Related to the pressure-signal characteristic curve (symbol V), ex works |
Inductive position switch: Electrical connection
The electrical connection is realized via a 4-pole mating connector (separate order, see "Accessories") with connection thread M12 x 1.
Inductive position switch: Switching logics
Position switch on side A, monitored spool position "0"

➀ | Central position (mechanical control spool overlap) |
➁ | Valve opening P→B |
➂ | Valve opening P→A |
Diagrams/characteristic curves
(measured with HLP46, ϑOil = 40 ±5 °C)
Pressure amplification measured with p = 100 bar)
![]() | ![]() |
Maximum zero flow of the main stage (symbol V) with pilot control valve

Maximum internal leakage of the main stage (symbol W) with pilot control valve

Flow command value function (Δp = 5 bar/control edge)
Symbol E, W and V, Version "L"

Flow command value function (Δp = 5 bar/control edge)
Symbol E, W and V, Version „P“

Size 10
Transition function with stepped electric input signals

Frequency response

Flow/load function with maximum valve opening (tolerance ±10 %)

Size 16
Transition function with stepped electric input signals

Frequency response

Flow/load function with maximum valve opening (tolerance ±10 %)

Size 25 and 27
Transition function with stepped electric input signals

Frequency response

Flow/load function with maximum valve opening (tolerance ±10 %)

Size 32
Transition function with stepped electric input signals

Frequency response

Flow/load function with maximum valve opening (tolerance ±10 %)

Size 35
Transition function with stepped electric input signals

Frequency response

Flow/load function with maximum valve opening (tolerance ±10 %)

Symbols/Circuit diagrams
Symbols

Symbol E1-, V1- and W8-: | |
P → A: qv max P → B: qv/2 | B → T: qv/2 A → T: qv max |
Version | simple | Detailed |
no code | ![]() | ![]() |
"E" | ![]() | |
"ET" | ![]() | |
"T" | ![]() |
1 | Pilot control valve |
2 | Main valve |
3 | Integrated electronics (OBE) |
4 | Design with spool position monitoring "M" |
Notice:
Representation according to DIN ISO 1219-1. Hydraulic interim positions are shown by dashes.
Electrical connection
Electrical connections and assignment
Connector pin assignment
Pin | Signal | Assignment interface "A1" | Assignment interface "F1" | Signal with interface A5 |
A | Power supply | 24 VDC | ||
B | 0 V | |||
C | Reference potential (actual value)/enable signal | Reference potential actual value (pin F) | Enable signal >11 VDC | |
D | Differential amplifier input (command value) | ± 10 V | 4 ... 20 mA | ± 10 V |
E | 0 V reference potential (pin D) | 0 V reference potential (pin D and F) | ||
F | Measuring output (actual value) | ± 10 V | 4 ... 20 mA | ± 10 V |
PE | Functional ground (directly connected to the valve housing) |
![]() | Command value | Reference potential at E and positive command value at D result in flow from P → A and B → T. |
Reference potential at E and negative command value at D result in flow from P → B and A → T. | ||
Connection cable (recommendation) | Up to 25 m cable length type LiYCY 7 x 0,75 mm2 | |
Up to 50 m cable length type LiYCY 7 x 1,0 mm2 | ||
Connect shield on PE only on the supply side |
Notices:
- Electrical signals provided via valve electronics (e.g. actual value) must not be used to switch off safety-relevant machine functions.
- Mating connectors, separate order, see "Accessories".
Block diagram: Integrated electronics (OBE)

Dimensions
Size 10
Dimensions in mm

![]() |
Required surface quality of the valve contact surface |
1 | Pilot control valve |
2 | Electrical connection |
3 | Wiring and mating connector |
4 | Inductive position transducer (pilot control valve) |
5 | Mating connectors, separate order, see "Accessories" |
6 | Name plate |
7 | Main valve |
8 | Integrated electronics (OBE) and inductive position transducer (main valve) |
9 | Identical seal rings for ports X and Y |
10 | Identical seal rings for ports A, B, P and T (T1) |
11 | Space required for connection cable and to remove the mating connector |
12 | Machined valve contact surface; Porting pattern according to ISO 4401-05-05-0-05 (ports X, Y as required) |
Valve mounting screws (separate order):
4 hexagon socket head cap screws ISO 4762 - M6 x 45 - 10.9-CM-Fe-ZnNi-5-Cn-T0-H-B
Tightening torque MA = 13,5 Nm ±10 %, material no. R913043777
or
4 hexagon socket head cap screws ISO 4762 - M6 x 45 - 10.9
Tightening torque MA = 15,5 Nm ±10 %, ot included in the Rexroth delivery range
Notice:
The tightening torque of the hexagon socket head cap screws refers to maximum operating pressure!
Size 16
Dimensions in mm

![]() |
Required surface quality of the valve contact surface |
1 | Pilot control valve |
2 | Electrical connection |
3 | Wiring and mating connector |
4 | Inductive position transducer (pilot control valve) |
5 | Mating connectors, separate order, see "Accessories" |
6 | Name plate |
7 | Main valve |
8 | Integrated electronics (OBE) and inductive position transducer (main valve) |
9 | Identical seal rings for ports X and Y |
10 | Identical seal rings for ports A, B, P and T (T1) |
11 | Space required for connection cable and to remove the mating connector |
12 | Machined valve contact surface, porting pattern according to ISO 4401-07-07-0-05 (ports X, Y as required). Deviating from the standard: ports A, B, P, T – Ø20 mm |
13 | Locking pin |
Valve mounting screws (separate order):
- 2 hexagon socket head cap screws ISO 4762 - M6 x 60 - 10.9-CM-Fe-ZnNi-5-Cn-T0-H-B
Tightening torque MA = 12.2 Nm ±10 %, material no. R913043410
- 4 hexagon socket head cap screws ISO 4762 - M10 x 60 - 10.9-flZn/nc/480h/C
Tightening torque MA = 58 Nm ±20 %, material no. R913014770
or
- 2 hexagon socket head cap screws ISO 4762 - M6 x 60 - 10.9
Tightening torque MA = 15,5 Nm ±10 %, not included in the Rexroth delivery range
- 4 Hexagon socket head cap screws ISO 4762 - M10 x 60 - 10.9
Tightening torque MA = 75 Nm ±20 %, not included in the Rexroth delivery range
Notice:
The tightening torque of the hexagon socket head cap screws refers to maximum operating pressure.
Size 25
Dimensions in mm

![]() |
Required surface quality of the valve contact surface |
1 | Pilot control valve |
2 | Electrical connection |
3 | Wiring and mating connector |
4 | Inductive position transducer (pilot control valve) |
5 | Mating connectors, separate order, see "Accessories" |
6 | Name plate |
7 | Main valve |
8 | Integrated electronics (OBE) and inductive position transducer (main valve) |
9 | Identical seal rings for ports X and Y |
10 | Identical seal rings for ports A, B, P, T |
11 | Space required for connection cable and to remove the mating connector |
12 | Machined valve contact surface; Porting pattern according to ISO 4401-08-08-0-05 (ports X, Y as required) |
13 | Locking pin |
Valve mounting screws (separate order):
6 hexagon socket head cap screws ISO 4762 - M12 x 60 - 10.9-flZn/nc/480h/C
Tightening torque MA = 100 Nm ±20 %, Material-Nr. R913015613
or
6 hexagon socket head cap screws ISO 4762 - M12 x 60 - 10.9
Tightening torque MA = 130 Nm ±20 %, not included in the Rexroth delivery range
Notice:
The tightening torque of the hexagon socket head cap screws refers to maximum operating pressure.
Size 27
Dimensions in mm

![]() |
Required surface quality of the valve contact surface |
1 | Pilot control valve |
2 | Electrical connection |
3 | Wiring and mating connector |
4 | Inductive position transducer (pilot control valve) |
5 | Mating connectors, separate order, see "Accessories" |
6 | Name plate |
7 | Main valve |
8 | Integrated electronics (OBE) and inductive position transducer (main valve) |
9 | Identical seal rings for ports X and Y |
10 | Identical seal rings for ports A, B, P, T |
11 | Space required for connection cable and to remove the mating connector |
12 | Machined valve contact surface; Porting pattern according to ISO 4401-08-08-0-05 (Ports X, Y as required) |
13 | Locking pin |
Valve mounting screws (separate order):
6 hexagon socket head cap screws ISO 4762 - M12 x 60 - 10.9-flZn/nc/480h/C
Tightening torque MA = 100 Nm ±20 %, Material-Nr. R913015613
or
6 hexagon socket head cap screws ISO 4762 - M12 x 60 - 10.9
Tightening torque MA = 130 Nm ±20 %, not included in the Rexroth delivery range
Notice:
The tightening torque of the hexagon socket head cap screws refers to maximum operating pressure.
Size 32
Size 32
Dimensions in mm

![]() |
Required surface quality of the valve contact surface |
1 | Pilot control valve |
2 | Electrical connection |
3 | Wiring and mating connector |
4 | Inductive position transducer (pilot control valve) |
5 | Mating connectors, separate order, see "Accessories" |
6 | Name plate |
7 | Main valve |
8 | Integrated electronics (OBE) and inductive position transducer (main valve) |
9 | Identical seal rings for ports X and Y |
10 | Identical seal rings for ports A, B, P, T |
11 | Space required to remove the mating connector |
12 | Machined valve contact surface; Porting pattern according to ISO 4401-10-09-0-05 (Ports X, Y as required). Deviating from the standard: |
13 | Locking pin |
Valve mounting screws (separate order):
6 hexagon socket head cap screws ISO 4762 - M20 x 80 - 10.9-flZn/nc/480h/C
Tightening torque MA = 340 Nm ±20 %, material no. R913008472
or
6 hexagon socket head cap screws ISO 4762 - M20 x 80 - 10.9
Tightening torque MA = 430 Nm ±20 %, not included in the Rexroth delivery range
Notice:
The tightening torque of the hexagon socket head cap screws refers to maximum operating pressure.
Size 35
Size 35
Dimensions in mm

![]() |
Required surface quality of the valve contact surface |
1 | Pilot control valve |
2 | Electrical connection |
3 | Wiring and mating connector |
4 | Inductive position transducer (pilot control valve) |
5 | Mating connectors, separate order, see "Accessories" |
6 | Name plate |
7 | Main valve |
8 | Integrated electronics (OBE) and inductive position transducer (main valve) |
9 | Identical seal rings for ports X and Y |
10 | Identical seal rings for ports A, B, P, T |
11 | Space required for connection cable and to remove the mating connector |
12 | Machined valve contact surface; Porting pattern according to ISO 4401-10-09-0-05 (Ports X, Y as required). Deviating from the standard: |
13 | Locking pin |
Valve mounting screws (separate order):
6 hexagon socket head cap screws ISO 4762 - M20 x 100 - 10.9-flZn/nc/480h/C
Tightening torque MA = 465 Nm ±20 %, material no. R913015670
or
6 hexagon socket head cap screws ISO 4762 - M20 x 100 - 10.9
Tightening torque MA = 610 Nm ±20 %, not included in the Rexroth delivery range
Notice:
The tightening torque of the hexagon socket head cap screws refers to maximum operating pressure.
Spool position monitoring "M" and electronics protection membrane "-967"
Dimensions in mm

14 | Electronics protection membrane "-967" |
15 | Spool position monitoring "M", optional |
NG | L1 | L2 |
mm | mm | |
10 | 240 | |
16 | 286 | 151 |
25 | 347 | 143 |
27 | 353 | 144 |
32 | 422 | 168 |
35 | 463 | 201 |
Notice:
The dimensions are nominal dimensions which are subject to tolerances.
Project planning information
Project planning, installation and commissioning
- When designing safety-related controls, observe the applicable industry-specific standards and regulations.
- Due to the flexible use of valves in systems, the user has to check and ensure that the product properties comply with all functional and safety requirements of the overall system.
- Make sure that there are no switching shocks and that the valve control spool does not vibrate.
- Valves with spool position indicator may only be installed, adjusted, commissioned and maintained by specialists trained in hydraulics and electronics.
- Improper work at safety-related parts of controls may result in personal injury and damage to property.
The following applies to all work carried out at the valve:
- Valves with spool position indicator must not be disassembled.
- The parts of the valves must not be exchanged.
- Integrated throttles must not be removed or modified.
- The spool position indicator may only be adjusted by the valve manufacturer.
Accessories
Mating connectors for valves with round connector, 6-pole + PE
7P Z31

Mating connectors for valves with round connector, 6-pole + PE
7P Z31
- For valves with round connector according to EN 175201-804, 6-pole + PE as well as 6-pole, compatible with VG 95328
Mating connectors for valves with round connector, 6-pole + PE, shielded, with assembled connection line
7P Z31 +
Mating connectors for valves with round connector, 6-pole + PE, shielded, with assembled connection line
7P Z31 +
- For valves with round connector according to EN 175201-804, 6-pole + PE as well as 6-pole, compatible with VG 95328
Mating connectors for sensors and valves with connector “K24”, “K35” and “K72”, M12 x 1
4P Z24

Mating connectors for sensors and valves with connector “K24”, “K35” and “K72”, M12 x 1
4P Z24
- For sensors and valves with connector “K24”, “K35” and “K72”
- Mating connectors M12, 4-pole, line cross-section 0.75 mm2
Mating connectors for sensors and valves with connector “K24”, “K35” and “K72”, M12 x 1, with assembled connection line
4P Z24 +

Mating connectors for sensors and valves with connector “K24”, “K35” and “K72”, M12 x 1, with assembled connection line
4P Z24 +
- For sensors and valves with connector “K24”, “K35” and “K72”
- Mating connectors M12, 4-pole, line cross-section 0.75 mm2
Mating connectors for sensors and valves with connector “K24”, “K35” and “K72”, M12 x 1, with assembled connection line, cable shielded
4P M12 +

Mating connectors for sensors and valves with connector “K24”, “K35” and “K72”, M12 x 1, with assembled connection line, cable shielded
4P M12 +
- For sensors and valves with connector “K24”, “K35” and “K72”
- Cable sets M12, 4-pole, line cross-section 0.34 mm2
Ordering codes
Downloads
Мы предлагаем следующие способы доставки товара:
Самовывоз из пункта выдачи
Самостоятельное получение заказа в пункте выдачи. Дата и время получения заранее согласуется с менеджером магазина.
Отгрузка товара юридическим лицам осуществляется только при наличии печати или правильно оформленной и заполненной доверенности, наличии паспорта получателя.
Курьерская доставка по Москве
Доставка по адресу покупателя или до пункта приема транспортной компании в г. Москве. Дата и время доставки заранее согласуется с менеджером магазина.
Доставка транспортной компанией по России
Доставка транспортной компанией по России до пункта выдачи транспортной компании или до конечного адреса покупателя.
Мы предлагаем следующие способы оплаты товара:
Оплата наличными
Оплата за наличный расчет для физических и юридических лиц. После внесения денежных средств Покупатель подписывает товаросопроводительные документы и получает кассовый чек.
Безналичная оплата
Мы работаем с физическими и юридическими лицами за безналичный расчёт со 100% предоплатой с оформлением всех предусмотренных законодательством документов. Счёт на оплату направляется Покупателю на электронную почту после запроса счета через форму на сайте либо по электронной почте. Цена на заказанный товар действительна в течение 2 дней с момента оформления Заказа.
Электронные способы
Оплата Заказа электронными способами, в т.ч. банковскими картами. Оплата Заказа данным способом доступна запросом ссылки на оплату у нашего менеджера.
Если у вас возникнут вопросы по оформлению заказа, вы можете обратиться к нам, позвонив по телефону +7 495 137-07-02 или связавшись по электронной почте sale@boschrexroth-russia.ru. Мы гарантируем оперативный ответ на ваш запрос и предоставление наилучших условий от официального поставщика Bosch Rexroth.
Мы предоставляем официальную гарантию на всю поставляемую продукцию Bosch Rexroth.
Гарантийный сервис включает в себя:
- Приемку продукции в сервисный центр для выполнения диагностики дефекта.
- Ремонт продукции.
- Доставку продукции до объекта заказчика.
- Телефон: +7 495 137-07-02
- E-mail: support@boschrexroth-russia.ru
Для расчета коммерческого предложения или получения счета на поставку оборудования и программного обеспечения Bosch Rexroth оставьте заявку в форме ниже или свяжитесь с отделом продаж по телефону +7 495 137-07-02 или электронной почте sale@boschrexroth-russia.ru. Мы гарантируем оперативный ответ на ваш запрос и предоставление наилучших условий от официального поставщика Bosch Rexroth.
Специалист по решениям Bosch Rexroth:
- Окажет профессиональную консультацию.
- Сообщит вашу цену на продукцию.
- Сообщит информацию об актуальных акциях и скидках.
- Подскажет ближайшее к вам отделение с наличием нужной продукции.
- Согласует с вами возможную дату и время доставки.

Нет отзывов об этом товаре.