Затрудняетесь с выбором?
Оставьте ваш телефон, и наш специалист перезвонит вам

Артикул: RX7371

Все товары Bosch Rexroth

Directional spool valves, direct operated, with solenoid actuation 5-.WE

Доступно к заказу

Цена по запросу

Получи КП от 5 лучших поставщиков
С указанием цены, наличия, сроков поставки и скидок.
И выбери подходящего.

Description

  • 5-chamber version
  • Size 10
  • Component series 5X
  • Maximum operating pressure 420 bar
  • Maximum flow 150 l/min

Features

  • 4/3-, 4/2- or 3/2-way version
  • Porting pattern according to ISO 4401-05-04-0-05
  • High-power solenoid, optionally rotatable by 90°
  • Electrical connection as individual connection
  • Use optionally with PWM connector (fast switching amplifier, energy reduction)
  • Optional auxiliary operating device
  • Spool position monitoring, optional
  • CE conformity according to the Low-Voltage Directive 2006/95/EC for electrical voltages >50 VAC or > 75VDC
  • Solenoid coil with UR approval UL 429
  • Approval according to CSA C22.2 no. 139-10, optional

Product description

The 5-chamber directional valve type 5-.WE is a solenoid-actuated directional spool valve with switching time increase. It controls the start, stop and direction of a flow. The directional valve basically consists of housing (1), one or two electronic solenoids (2), control spool (3), and the return springs (4).

In de-energized condition, the control spool (3) is held in the central position or in the initial position by the return springs (4) (except for valves without spring "O").

If the wet-pin electronic solenoid (2) is energized, the control spool (3) moves out of its rest position into the required end position. In this way, the required direction of flow according to the selected symbol is released.

After the electronic solenoid (2) has been switched off, the control spool (3) is pushed back into the central position or in the initial position (except for valve with "OF" detent and valve without spring type "O").

A manual override (6) allows for the manual switching of the valve without solenoid energization.

To ensure proper functioning, make sure that the pressure chamber of the solenoid is filled with oil.

Type 5-4WE 10 …

Throttle insert

Using a throttle insert (9) in channels P, A, B or T, the flow resistance at the valve can be increased. Its use is required when, due to prevailing operating conditions, flows occur during the switching processes, which exceed the performance limit of the valve.

Without spring return “O” (only possible with symbols A, C and D)

This version is a directional valve with 2 spool positions and 2 electronic solenoids without detent. The valve without spring return at the control spool (3) does not have a defined basic position in the de-energized condition.

Without spring return with detent “OF” (only possible with symbols A, C and D)

This version is a directional valve with 2 spool positions and 2 electronic solenoids with detent. The detents are used to lock the control spool (3) in the relevant spool position. During operation, continuous application of current to the electronic solenoid can thus be omitted which contributes to energy-efficient operation.

Notice:

Pressure peaks in the tank line to two or several valves can result in unintended movements of the control spool in the case of valves with detent. We therefore recommend that separate return lines be provided or a check valve installed in the tank line.

Influencing the switching time

With the 5-chamber directional valve type 5-.WE, the switching time can be delayed to 100 ms and more by means of a throttle screw "C" (7) or a selected orifice "A0.” (8). In this connection, the switching time is pressure-, flow- and viscosity-dependent, specific to the installation. The switching time is influenced by means of a restriction (throttle or orifice) in the connection channel (5) between the two spring chambers in which the liquid volume is displaced from one spring chamber into the other in case of a switching process.

The T channels are separated from the spring chambers in order to achieve soft switching.

Notices!

The adjustment spindle (10) may only be screwed out so that it protrudes from the nut by max. 3 mm.

Type code

01

02

03

04

05

06

07

08

09

10

11

12

13

14

15

16

17

18

19

20

5

-

WE

10

-

5X

/

E

/

=

*

01

Standard version (maximum operating pressure 350 bar)

no code

High-pressure version (maximum operating pressure 420 bar)

H

02

5-chamber version

5

03

3 main ports

3

4 main ports

4

04

Directional valve

WE

05

Size 10

10

06

Symbols e. g. C, E, EA, EB, etc.; for the possible version, see Symbols

07

Component series 50 … 59 (50 … 59: unchanged installation and connection dimensions)

5X

Spool return

08

With spring return

no code

With reinforced compression spring (for quick switching off)

D

Without spring return

O

Without spring return with detent

OF

09

High-power solenoid, wet-pin, with detachable coil

E

10

Direct voltage 12 V

G12

Direct voltage 24 V

G24

Direct voltage 26 V

G26

Direct voltage 48 V

G48

Nominal voltage 96 V at DC solenoid in operation with AC voltage mains (AC voltage mains 100/110 V - 50/60 Hz with an admissible voltage tolerance of +/- 10 %)

G96

Direct voltage 110 V

G110

Direct voltage 125 V

G125

Nominal voltage 180 V at DC solenoid in operation with AC voltage (AC voltage mains 200 V - 50/60 Hz with an admissible voltage tolerance of +/- 10 %)

G180

Nominal voltage 205 V at DC solenoid with operation with AC voltage mains (AC voltage mains 230 V – 50/60 Hz with an admissible voltage tolerance of +/- 10 %)

G205

Direct voltage 220 V

G220

Connection to AC voltage mains via control with rectifier (see table Mating connectors)

Electrical connections and available voltages see Technical data

11

Without manual override

no code

With concealed manual override (standard)

N9 1)

With concealed manual override and protective cap

3)

N8 1)

With lockable manual override "mushroom button" (large)

N5 1;2)

With manual override "mushroom button" (large), not lockable

N6 1)

Corrosion resistance (outside)

12

None (valve housing primed)

no code

Improved corrosion protection (240 h salt spray test according to EN ISO 9227); (only version "K4K")

J3

Electrical connection

5)

13

Individual connection

Without mating connector, with connector DIN EN 175301-803

K4 4)

Without mating connector, with connector DIN EN 175301-803 (coil with potted-in connector base and sealing element to valve housing (IP67); possible with version "J3")

K4K 4)

Without mating connector, 4-pole with connector M12x1, integrated interference protection circuit, status LED according to IEC 60947-5-2

K72L 4;5)

Without mating connector; connector AMP Junior-Timer

C4Z 4)

For further electrical connections and available voltages, see Technical data

Spool position monitoring

14

Without position switch

no code

Inductive position switch type QM

Monitored spool position "a"

QMAG24

Monitored spool position "b"

QMBG24

Monitored spool position "0"

QM0G24

Inductive position switch type QS

Monitored spool position "a"

QSAG24W

Monitored spool position "b"

QSBG24W

Monitored spool position "0"

QS0G24W

Monitored spool position "0" and "a"

QS0AG24W

Monitored spool position "0" and "b"

QS0BG24W

Monitored spool position "a" and "b"

QSABG24W

For further details, see data sheet 24830

Switching time increase

15

Without switching time increase

no code

With throttle screw

C

With orifice Ø 0.6 mm

A06

With orifice Ø 0.8 mm

A08

With orifice Ø 1.0 mm

A10

Throttle insert

16

Without throttle insert

no code

With throttle insert

6); 7) :

Port

Throttle Ø in mm

0,8 mm

1,0 mm

1,2 mm

P

B08

B10

B12

A

H08

H10

H12

B

R08

R10

R12

A and B

N08

N10

N12

T 8)

X08

X10

X12

Further throttle insert diameters upon request

Control spool play

17

Standard

no code

Minimum (to be selected in case of reduced leakage → higher level of oil cleanliness recommended)

T06

Increased (to be selected in case of a hydraulic fluid/environment temperature difference >25 K → increased internal leakage)

T12

Seal material

18

NBR seals

M

FKM seals

V

Seals for HFC hydraulic fluids

MH

Low-temperature version

MT

Observe compatibility of seals with hydraulic fluid used. (Other seals upon request)

19

Approval according to CSA C22.2 no. 139-10

CSA

Porting pattern according to ANSI B93.9 (if solenoid "a" is energized, channel P is connected to A)

AN

20

Further details in the plain text

*

1) The manual override cannot be allocated a safety function. The manual override units may only be used up to a tank pressure of 50 bar.
2) With tank pressures above 50 bar, it cannot be guaranteed that the valve remains in the position switched by the manual override "N5".
3) Protective cap must be removed prior to actuation.
4) Mating connectors, separate order, see table Mating connectors and data sheet 08006.
5) M12x1 plug-in connection see data sheet 08010.
6) When the admissible valve performance limits are exceeded, installation of throttle inserts is to be intended (performance limits see 2 spool positions).
7) Not with low-temperature version "MT".
8) When throttle inserts are used in channel T, the pressure in the working ports and in case of connection to the tank chambers must not exceed 210 bar.

AC voltage mains (admissible voltage tolerance ± 10%)

Nominal voltage of the DC solenoid in case of operation with alternating voltage

Ordering code

100 V - 50/60 Hz

96 V

G96

100 V - 50/60 Hz

96 V

G96

200 V - 50/60 Hz

180 V

G180

230 V - 50/60 Hz

205 V

G205

Notice:

Conversion from AC voltage to DC voltage requires a mating connector with rectifier (separate order, material no. R901017025).

Technical data

Diagrams/characteristic curves

(measured with HLP46, ϑOil = 40 °C ± 5 °C)

Δp-qV characteristic curves

Symbol

Direction of flow

Symbol

Direction of flow

P - A

P - B

A - T

B - T

P - A

P - B

A - T

B - T

P - T

A

4

4

F

1

3

3

8

4

B

4

5

G

4

5

6

8

7

C, J, Q, Y

2

3

5

7

H

1

1

6

8

7

D

2

2

5

7

P

3

1

5

6

5

E

3

3

6

7

E - „QS“

3

2

6

7

E34

5

5

8

E67

3

4

4

7

H

1

1

6

8

J19

7

9

9

L, Y11

3

3

5

7

R

3

4

5

6

U

2

2

5

7

W

2

2

5

6

X7

3

6

Characteristic curve for symbol G41 upon request.

Performance limits: 2 spool positions (measured with HLP46, ϑOil = 40 ±5 °C)

Notice!

The specified switching power limits are valid for use with two directions of flow (e. g. from P to A and simultaneous return flow from B to T).

Due to the flow forces acting within the valves, the admissible switching power limits may be considerably lower with only one direction of flow (e. g. from P to A while port B is blocked)!

In such use cases, please consult us!

The switching power limit was established while the solenoids were at operating temperature, at 10 % undervoltage and without tank preloading.

Spring side

Characteristic curve

Symbol

1

B

Solenoid side

Characteristic curve

Symbol

2

A, B

3

C; Y11

4

D

5

Y

6

X7

Performance limits: 3 spool positions (measured with HLP46, ϑOil = 40 ±5 °C)

Notice!

The specified switching power limits are valid for use with two directions of flow (e. g. from P to A and simultaneous return flow from B to T).

Due to the flow forces acting within the valves, the admissible switching power limits may be considerably lower with only one direction of flow (e. g. from P to A while port B is blocked)!

In such use cases, please consult us!

The switching power limit was established while the solenoids were at operating temperature, at 10 % undervoltage and without tank preloading.

Spring side

Characteristic curve

Symbol

7

E

8

F

9

G

10

H

11

J; J19

12

L

Solenoid side

Characteristic curve

Symbol

7

E

8

F

9

G

11

J, J19

12

L

13

E34

Characteristic curves for symbols G41 and P upon request.

Notice!

The specified switching power limits are valid for use with two directions of flow (e. g. from P to A and simultaneous return flow from B to T).

Due to the flow forces acting within the valves, the admissible switching power limits may be considerably lower with only one direction of flow (e. g. from P to A while port B is blocked)!

In such use cases, please consult us!

The switching power limit was established while the solenoids were at operating temperature, at 10 % undervoltage and without tank preloading.

Solenoid side

Characteristic curve

Symbol

14

E67

15

E ‒ „QS“

16

U

17

R

18

W

Symbols/Circuit diagrams

2 spool positions

Notices!

  • Representation according to DIN ISO 1219-1. Hydraulic interim positions are shown by dashes.
  • Other symbols upon request

3 spool positions

1)Example:
● Symbol E with spool position “a” ordering code ..EA..
● Symbol E with spool position “b” ordering code ..EB..
2)For symbol Q and W, see “Flow cross-section" in the technical data

Notices!

  • Representation according to DIN ISO 1219-1. Hydraulic interim positions are shown by dashes.
  • Other symbols upon request.

Inductive position switch type QM Switching logics

Version QMA

Position switch on side B, monitored spool position "a"

Version QMA

Position switch on side A, monitored spool position "a"

Version QMB

Position switch on side B, monitored spool position "b"

Version QMB

Position switch on side A, monitored spool position "b"

Version QM0

Position switch on side B, monitored rest position

Version QM0

Position switch on side A, monitored rest position

Inductive position switch type QL: switching logics

Version QLA

Position switch on side B, monitored spool position "a"

Version QLA

Position switch on side A, monitored spool position "a"

Version QLB

Position switch on side B, monitored spool position "b"

Version QLB

Position switch on side A, monitored spool position "b"

Inductive proximity sensor type QS: electrical connection

1

Width depending on hysteresis and temperature drift

2

Overlap in the monitored spool position

3

Signal flow (in the switching position to be monitored)

4

Signal flow (leaving the monitored switching position)

5

Beginning of the overlap

6

Switching point

7

Stroke end

8

Not monitored spool position

9

Monitored spool position

Inductive proximity sensor type QS: Switching logics

Version QSAG24W (valves with 3 spool positions, e.g. symbols E, J, G, …)

(Proximity sensor on side B, monitored spool position "a")

Version QSBG24W (valves with 3 spool positions, z. B. symbols E, J, G, …)

(Proximity sensor on side A, monitored spool position “b”)

Version QS0G24W (valves with 3 spool positions, z. B. symbols E, J, G, …)

(Proximity sensor on side A and B, monitored rest position)

Version QSABG24W (valves with 3 spool positions, e.g. symbols E, J, G, …)

(Proximity sensor on side A and B, monitored spool position "a" and "b")

Version QSABG24W (valves with 2 spool positions, e. g. symbols A, B, D, Y, …)

(Proximity sensor on side A and B, monitored spool position "a" and "b")

Version QS0BG24W (valves with 2 spool positions, e.g. symbols EB, …)

(Proximity sensor on side A and B, monitored spool position “0” and "b")

Version OF…QSAG24W

(Proximity sensor on side B, monitored spool position "a")

Version OF…QSBG24W

(Proximity sensor on side A, monitored spool position “b”)

Version OF…QSABG24W

(Proximity sensor on side A and B, monitored spool position "a" and "b")

Electrical connection

Over-current fuse and switch-off voltage peaks

M12x1 plug-in connection ‒ Individual connection – “K72L”

Pin 5 without function

Maximum admissible overvoltages according to DIN EN 60664-1:2008-01 (VDE 0110-1) (overvoltage category II):

Electrical connection

1)

Nominal voltage in V

Rated current in A

Maximum admissible

Switch-off overvoltage in V

2)​

K4, K4K

12

3,72

500

K4, K4K, K72L

24

1,74

500

K4, C4Z

26

1,70

500

K4

48

0,57

500

K4

96

0,47

500

K4

125

0,22

500

K4, C4Z

180

0,28

500

K4

205

0,22

500

K4

220

0,21

500

1)Interference protection circuit integrated
2)To be ensured by user circuitry

Notice:

When solenoid coils are switched off, voltage peaks result which may cause faults or damage in the connected control electronics. We therefore recommend limiting them to 2 x nominal voltage by means of an interference protection circuit. It must be noted that a diode switched in an antiparallel form extends the switching off time.

Electrical connections, assignment

Electrical connections and coil connection combinations

Ordering code connector

Top view

Circuit diagram

Pin

Connections, assignment

3-pole connector (2+PE) according to DIN EN 175301-803

K4, K4K 1)

1

Solenoid coil, polarity-independent

2

Earthed

Earthing

4-pole connector according to IEC 60947-5-2, M12x1 with suppressor diode, only 24 V DC, integrated interference protection circuit and status LED

K72L

1

Internal bridge

2

3

Solenoid coil GND

4

Solenoid coil 24 VDC supply voltage

5

Without function

2-pole connector, type AMP Junior-Timer, rotated by 90° relative to valve axis

C4Z

1

Solenoid coil, polarity-independent

2

1)M3, tightening torque maximum MA max = 0.5 Nm
2)Coil with potted-in connector base and sealing element to valve housing (IP67)

Mating connectors according to DIN EN 175301-803

For details and more mating connectors see data sheet 08006

Connection

Valve side

Color

Material number

Without circuitry

With indicator light

12 ... 240 V

With rectifier

12 ... 240 V

With indicator light and Zener diode suppression circuit

24 V

M16 x 1,5

a

gray

R901017010

a/b

black

R901017011

R901017022

R901017025

R901017026

1/2″ NPT
(Pg16)

a

red/brown

R900004823

a/b

black

R900011039

R900057453

R900842566

Energy savings and fast switching

1)​

Details see data sheet 30362

Material number

Type VT-SSBA1-PWM-1X/V001/5 as fast switching amplifier (switching time reduction by approx. 50 %)

2)

Type VT-SSBA1-PWM-1X/V002/5 for energy reduction (energy saving by approx. 40 %)

3)

a/b

black

R901265633

R901290194

1)Only with J2 and X84; not for version “D”
2)Only for version “G12” and “K4/K4K”
3)Only for version “G24” and “K4/K4K”

Cartridge with PWM connector according to data sheet 30362:

  • Depending on the control spool, increasing the performance limit is possible.
  • With version "G24" (energy saving), the coil temperature is reduced by ≥ [si]30 °C[s/i][imp]86 °F[/imp] for 100 % duty cycle.

Dimensions

Dimensions in mm

1.1

Solenoid “a”

1.2

Solenoid “b”

5.1

Mating connector without circuitry for connector "K4", separate order, see "Accessories"

5.2

Mating connector without circuitry for connector "K4K" (separate order, see data sheet 08006)

5.3

Mating connector angled with M12x1 plug-in connection and status LED for connector "K72L", separate order, see "Accessories"

5.4

Double valve mating connector without/with circuitry for “K4” connector (separate order, see data sheet 08006)

5.5

Mating connector (AMP Junior Timer) for connector "C4Z" (separate order, see data sheet 08006)

6

Mating connector with circuitry for “K4” connector, separate order, see "Accessories"

7

Name plate

8

Identical seal rings for ports A, B, P, TA, TB

9.1

Name plate

9.2

Plug screw for valves with one solenoid

10

Identical seal rings for ports A, B, P, TA, TB

11

Plug screw for valves with one solenoid

12

Space required to remove the mating connector/angled socket

13

Space required to remove the coil

14

Mounting nut, tightening torque MA = 14.5±1.5  Nm

Notice:

  • Deviating from ISO 4401, port T is referred to as TA and port T1 is referred to as TB in this data sheet.
  • The dimensions are nominal dimensions which are subject to tolerances.

Subplates according to data sheet 45054 (separate order)

G 66/01 (G3/8)

G 67/01 (G1/2)

G 534/01 (G3/4)

G 66/12 (SAE-6; 9/16-18)1)

G 67/12 (SAE-8; 3/4-16)1)

G 534/12 (SAE-12; 1-1/16-12)1)

1) upon request

Valve mounting screws (separate order)

4 hexagon socket head cap screws, metric

ISO 4762 - M6 x 40 - 10.9-flZn-240h-L

(friction coefficient μtotal = 0.09 to 0.14);

tightening torque MA = 12.5 Nm ± 10 %,

material no. R913000058

or

4 hexagon socket head cap screws

ISO 4762 - M6 x 40 - 10.9 (self procurement)

(friction coefficient µtotal = 0.12 to 0.17);

tightening torque MA = 15.5 Nm ± 10 %

4 hexagon socket head cap screws UNC

1/4-20 UNC x 1-1/2″ ASTM-A574

(friction coefficient µtotal = 0.19 to 0.24);

Tightening torque MA = 25 Nm ± 15 %,

(friction coefficient µtotal = 0.12 to 0.17);

tightening torque MA = 19 Nm ± 10 %,

material no. R978800710

With different friction coefficients, the tightening torques are to be adjusted accordingly!

Manual override

Dimensions in mm

2

Version without and with concealed manual override "N9" (standard)

3

Version with concealed manual override and protective cap "N8". (The protective cap must be removed prior to actuation.)

4

Version with manual override "N5" and “N6

Notice:

The dimensions are nominal dimensions which are subject to tolerances.

Subplates according to data sheet 45054 (separate order)

G 66/01 (G3/8)

G 67/01 (G1/2)

G 534/01 (G3/4)

G 66/12 (SAE-6; 9/16-18)1)

G 67/12 (SAE-8; 3/4-16)1)

G 534/12 (SAE-12; 1-1/16-12)1)

1) upon request

Valve mounting screws (separate order)

4 hexagon socket head cap screws, metric

ISO 4762 - M6 x 40 - 10.9-flZn-240h-L

(friction coefficient μtotal = 0.09 to 0.14);

tightening torque MA = 12.5 Nm ± 10 %,

material no. R913000058

or

4 hexagon socket head cap screws

ISO 4762 - M6 x 40 - 10.9 (self procurement)

(friction coefficient µtotal = 0.12 to 0.17);

tightening torque MA = 15.5 Nm ± 10 %

4 hexagon socket head cap screws UNC

1/4-20 UNC x 1-1/2″ ASTM-A574

(friction coefficient µtotal = 0.19 to 0.24);

Tightening torque MA = 25 Nm ± 15 %,

(friction coefficient µtotal = 0.12 to 0.17);

tightening torque MA = 19 Nm ± 10 %,

material no. R978800710

With different friction coefficients, the tightening torques are to be adjusted accordingly!

Spool position monitoring

Dimensions in mm

Inductive position switch type QM

Dimensions in mm

1)For dimensions, see valve dimensions

Notice:

The dimensions are nominal dimensions which are subject to tolerances.

Spool position monitoring

Inductive position switch type QL

Dimensions in mm

1)For dimensions, see valve dimensions

Mounting cavity R/T-11A; 3 main ports; thread M20 x 1.5 mm

Dimensions in mm

Notice!

The dimensions are nominal dimensions which are subject to tolerances.

Spool position monitoring

Inductive position switch type QS

Dimensions in mm

Mounting cavity, 2 main ports; M20 x 1.5 thread

Version "C"
Dimensions in mm

Notice:

The dimensions are nominal dimensions which are subject to tolerances.

M12x1 plug-in connection ‒ Individual connection

Dimensions in mm

Type 5-.WE 10 .3X/.CG24.K72L…

Dimensions in mm

Project planning information

Temperature range and maximum operating pressure in case of use at low temperatures

Port

Pressure

Temperature range in °C

‒ P, A, B, T

static 100 bar

–40 … –35

‒ P, A, B

dynamic from 100 bar to 350 barin linear form as a function of the temperature

–35 … –30

‒ T

dynamic from 100 bar to 210 bar in linear form as a function of the temperature

–35 … –30

‒ P, A, B, T

Maximum operating pressure

–30 … +50

Accessories

Mating connectors for valves with connector “K4”, without circuitry, standard

3P Z4

Mating connectors for valves with connector “K4”, without circuitry, standard

3P Z4

  • For valves with connector “K4” according to EN 175301-803 and ISO 4400, 2-pole + PE, “large cubic connector”
  • Mating connectors for valves with one or two solenoids (individual connection)

Mating connectors for valves with connector “K4”, without circuitry, standard

3P Z45

Mating connectors for valves with connector “K4”, without circuitry, standard

3P Z45

  • For valves with connector “K4” according to EN 175301-803 and ISO 4400, 2-pole + PE, “large cubic connector”
  • Mating connectors for valves with one or two solenoids (individual connection)

Mating connectors for valves with connector “K4”, with indicator light

3P Z5L

Mating connectors for valves with connector “K4”, with indicator light

3P Z5L

  • For valves with connector “K4” according to EN 175301-803 and ISO 4400, 2-pole + PE, “large cubic connector”
  • Mating connectors for valves with one or two solenoids (individual connection)

Mating connectors for valves with connector “K4”, with indicator light

3P Z55L

Mating connectors for valves with connector “K4”, with indicator light

3P Z55L

  • For valves with connector “K4” according to EN 175301-803 and ISO 4400, 2-pole + PE, “large cubic connector”
  • Mating connectors for valves with one or two solenoids (individual connection)

Mating connectors for valves with connector “K4”, with indicator light and Zener diode suppression circuit

3P Z5L1

Mating connectors for valves with connector “K4”, with indicator light and Zener diode suppression circuit

3P Z5L1

  • For valves with connector “K4” according to EN 175301-803 and ISO 4400, 2-pole + PE, “large cubic connector”
  • Mating connectors for valves with one or two solenoids (individual connection)

Mating connectors for valves with connector “K4”, with rectifier

3P RZ5

Mating connectors for valves with connector “K4”, with rectifier

3P RZ5

  • For valves with connector “K4” according to EN 175301-803 and ISO 4400, 2-pole + PE, “large cubic connector”
  • Mating connectors for valves with one or two solenoids (individual connection)

Mating connectors for valves with connector “K4”, with rectifier

3P RZ55

Mating connectors for valves with connector “K4”, with rectifier

3P RZ55

  • For valves with connector “K4” according to EN 175301-803 and ISO 4400, 2-pole + PE, “large cubic connector”
  • Mating connectors for valves with one or two solenoids (individual connection)

Downloads

Directional spool valves, direct operated, with solenoid actuation
Data Sheet | RE23352 | 2015-09-01 | English | PDF | 972k

Product Groups: Direct operated
Type 5-.WE, 5-chamber version

Мы предлагаем следующие способы доставки товара:

Самовывоз из пункта выдачи

Самостоятельное получение заказа в пункте выдачи. Дата и время получения заранее согласуется с менеджером магазина.
Отгрузка товара юридическим лицам осуществляется только при наличии печати или правильно оформленной и заполненной доверенности, наличии паспорта получателя.


Курьерская доставка по Москве

Доставка по адресу покупателя или до пункта приема транспортной компании в г. Москве. Дата и время доставки заранее согласуется с менеджером магазина.

Доставка транспортной компанией по России

Доставка транспортной компанией по России до пункта выдачи транспортной компании или до конечного адреса покупателя. 
 

Для расчета коммерческого предложения или получения счета на поставку оборудования и программного обеспечения Bosch Rexroth оставьте заявку в форме ниже или свяжитесь с отделом продаж по телефону +7 495 137-07-02 или электронной почте sale@boschrexroth-russia.ru. Мы гарантируем оперативный ответ на ваш запрос и предоставление наилучших условий от официального поставщика Bosch Rexroth. 

Специалист по решениям Bosch Rexroth:

  • Окажет профессиональную консультацию.
  • Сообщит вашу цену на продукцию.
  • Сообщит информацию об актуальных акциях и скидках.
  • Подскажет ближайшее к вам отделение с наличием нужной продукции.
  • Согласует с вами возможную дату и время доставки.

Запрос цены или КП

Запрос цен, наличия или консультация
Пришлем актуальную информацию по ценам, скидкам, наличию товара на складе и срокам поставки
НовостиВсе новости
Bosch Rexroth A4FO: надежность в условиях высокого давления

Гидравлическое оборудование остается важной частью современных промышленных и строительных систем. Аксиально-поршневой насос Bosch Rexroth A4FO демонстрирует, как сочетание универсальности, долговечности и инженерной точности помогает решать сложные задачи, связанные с подачей гидравлической жидкост..

17 Января, 2025
Bosh Rexroth: Эффективность и надежность в одном решении

Синхронные моментные двигатели MBT130, представляющие серию MST130+MRT130 от Bosh Rexroth, выделяются рядом особенностей, которые могут быть важны для самых различных применений в автоматизации и промышленности. Кратко о характеристиках: - Максимальный крутящий момент до 180 Нм, что позвол..

14 Декабря, 2024
Bosh Rexroth HED 5-3X: Надежный контроллер для современных систем

Гидроэлектрические реле давления поршневого типа HED 5-3X от производителя Bosh Rexroth завоевали признание среди специалистов благодаря своим выдающимся характеристикам и функциональности. Эти устройства обеспечивают надежный контроль давления в различных промышленных системах. Серия компонентов..

16 Ноября, 2024
Bosch Rexroth - новая эра измерения давления в гидравлических системах

В условиях современного производства всегда важно обеспечивать стабильность и безопасность работы гидравлических систем. Преобразователь давления HM20-2X становится эффективным решением для этой задачи. Среди ключевых характеристик HM20-2X стоит выделить следующие - Серия компонент..

14 Октября, 2024
Boschrexroth Датчик давления HED 8 OA-2X/100K14: надежность и точность в контроле давления

Датчик давления Boschrexroth HED 8 OA-2X/100K14 (арт. R901102706) используется в различных промышленных приложениях, обеспечивая высокую точность и надежность измерений давления. Он способен функционировать в строгих условиях, что делает его незаменимым инструментом для автоматизации и управления пр..

13 Сентября, 2024
Bosh Rexort - аккумуляторы HAD оптимизируют энергосистемы

В мире гидропневматических систем появилась новинка, которая уже привлекла внимание специалистов. Гидропневматические аккумуляторы серии HAD демонстрируют инновационный подход к управлению энергией и стабилизации давления в различных системах, как мобильных, так и стационарных. Высокая эффективно..

23 Августа, 2024
Bosh Rexort представило двухходовой патронный клапан!

Двухходовой патронный клапан с активным управлением LC2A Bosch Rexroth представляет собой прецизионное гидравлическое устройство, разработанное для контроля и регулирования потока рабочей жидкости в системах гидравлики. Этот клапан работает по принципу двухпозиционного управления потоком, обеспечива..

17 Июля, 2024
Bosch Rexroth - надежный партнер для вашего бизнеса в области гидравлики!

Компания Bosch Rexroth предлагает широкий спектр продукции, включая гидронасосы, гидромоторы, гидроклапана, гидроцилиндры, пневмоцилиндры, клапаны, регуляторы, датчики и многое другое. Благодаря высокому качеству продукции и многолетнему опыту работы в отрасли, Bosch Rexroth является предпочтит..

20 Июня, 2024
Как правильно выбрать насос от BOSCH REXROTH?

В мире мобильной и промышленной гидравлики, где надежность и качество стоят на первом месте, насосы Bosch Rexroth выделяются как эталон долговечности и технического совершенства. Эти изделия, зарекомендовавшие себя в России и за её пределами, стали символом немецкого качества и профессионального под..

30 Мая, 2024
Bosch Rexroth – гидравлические шестерённые насосы серии AZPF

Гидравлические шестерённые насосы серии AZPF - это оборудование, которое обеспечивает преобразование механической энергии в гидравлическую с высоким КПД. Они обладают длительным сроком службы благодаря уплотнению зазоров и высокоточной технологии производства. Приводные валы в соответствии с межд..

8 Апреля, 2024
Bosch Rexroth на выставке LogiMAT

На выставке LogiMAT компания Bosch Rexroth представила передовые компоненты, подсистемы и системные решения для автоматизации и оптимизации логистики. Среди предложений компании - практические решения для трансмиссии и рабочих функций промышленных грузовиков и автономных мобильных роботов (AMR), вкл..

22 Марта, 2024
Bosch Rexroth открывает новые возможности в управлении машинами и подключении к IoT

Bosch Rexroth предлагает одну из самых производительных систем ЧПУ на рынке. Компания является лидером в области автоматизации и устанавливают стандарты в этой области. От датчиков и сервоприводов до революционной новой платформы, Bosch Rexroth предлагает широкий спектр решений для автоматизации. ..

16 Февраля, 2024

Нет отзывов об этом товаре.

Написать отзыв

Рейтинг