Затрудняетесь с выбором?
Оставьте ваш телефон, и наш специалист перезвонит вам

Артикул: RX7796

Все товары Bosch Rexroth

Pressure and flow control system SYHDFEF-1X

Доступно к заказу

Цена по запросу

Получи КП от 5 лучших поставщиков
С указанием цены, наличия, сроков поставки и скидок.
И выбери подходящего.

Description

  • With axial piston variable displacement pump A4VSO
  • Size 40 … 355
  • Component series 1X
  • Maximum operating pressure 350 bar
  • Function: Swivel angle control, Pressure control,Torque limitation, Speed control function, Master-Slave
  • Communication: Sercos, PROFINET, EtherNET/IP, POWERLINK, VARAN, CAN over EtherCAT, ServoDrive over EtherCAT, analog

Features

  • The control system is used for the electro-hydraulic control of swivel angle, pressure and power (partially optional) of an axial piston variable displacement pump.
    It consists of the following components:
  • A4VSO axial piston variable displacement pump optimized for the operation in the control system
  • VT-DFP. proportional valve as pilot control valve with integrated electronics including inductive position transducer for valve position sensing.
  • Position transducer for sensing the swivel angle
  • Pressure transducer with suitable signal level and dynamics (optional)

Product description

1

Swash plate

2

Pilot control valve

3

Counter piston

4

Actuating piston

5

Spring

6

Inductive position transducer for valve position

7

Swivel angle position sensor

8

Proportional solenoid

9

Valve spool

10

Spring

11

Integrated electronics

15

Drive shaft

16

Connection flange

17

Subplate, optionally with through-drive

19

Multi Ethernet interface X7E1

20

Multi Ethernet interface X7E2

25

Actual swivel angle value input X8A1

26

Configurable sensor interface X2N

27

Connector XH1

Type code

01

02

03

04

05

06

07

08

09

10

11

12

13

14

15

16

17

SYHDFEF

1X

/

B

25

A

A

*

Pump of the control system

Series

01

Control system with internal digital electronics (Ethernet-based bus systems)

SYHDFEF

Pump combinations (see below)

SY2HDFEF
SY3HDFEF

02

Component series 10 ... 19 (10 ... 19: unchanged installation and connection dimensions)

1X

Size

040

071

125

180

250

355

03

Displacement cm³

40

71

125

180

250

355

e.g. 071

Direction of rotation looking at the drive shaft

04

Right

R

Left

L

Hydraulic fluid

05

Mineral oil according to DIN 51524 (HL/HLP)

V

HFC

F

Drive shaft variant

06

Cylindrical with fitting key DIN 6885 (not in connection with through-drive)

P

Splined shaft profile DIN 5480

Z

Connection flange

07

ISO 4-hole

B

Port for working lines pressure port B and suction port S

08

Port B and S: SAE, laterally displaced by 90°, metric mounting thread, 2nd pressure port B1 vis-à-vis B – upon delivery closed by means of flange plate

25

Through-drive (All through-drives with single pumps come without a hub and are operationally safe, provided with an end cover)

09

Without through-drive

N00

Universal through-drive, closed operationally safe with end cover at the factory; for components for the adaptation of more pump stages, see "Accessories".

U99

Through-drive, closed operationally safe with end cover at the factory; for components for the adaptation of more pump stages, see "Accessories".

K99

Centering: SAE ⌀82,55 mm
Attachment pump (examples): A10VSO..31 NG18, PGF2M, PGH2, PGH3, AZPF

1)

KC1

Base pump variant

10

Standard (internal pilot oil)

0000

External supply

0576

1)Observe the conditions for the attachment pumps.

Pilot control and preload valve

Control spool design

11

Standard

A

Installation orientation of the integrated electronics (see below and "Dimensions")

12

Parallel to the pump axis

0

Vertical to the pump axis

1

Additional functions: Closed-loop control

13

Standard

A

Fieldbus interface

14

Sercos III

S

EtherCAT (Profil CANopen)

T

EtherCAT (Servodrive profile)

D

VARAN (servo drive profile)

V

EtherNet/IP

E

PROFINET RT

N

Actual pressure value input (freely configurable); Parameter setting upon delivery (see "Electrical connections")

15

Voltage input 0 … 10 V

Port XH4

V

Voltage input 0.5 … 5 V

Port X2N

F

Pressure transducer

16

HM 20-2X/315-F-C13-0.5, measurement range 315 bar (0.5 ... 5 V) with connection cable 0.5 m for direct connection to X2N (only version "F")

L

Without pressure transducer

X

17

Further details in the plain text

*

Installation orientation of the valve electronics

Clockwise direction of rotation

Installation orientation "0"

Installation orientation "1"

Pump combinations

(Material numbers or type designations are to be connected by means of "+")

01

02

03

04

05

06

SY2HDFEF

1X

/

/

+

01

Two-way pump

SY2HDFEF

02

Component series 10 ... 19 (10 ... 19: unchanged installation and connection dimensions)

1X

03

Size of the main pump

1)

04

Size of the attachment pump or pump abbreviation if the attachment pump is not SYHDFE (e.g. PGF)

1)

05

Material number without "R9" for the main pump or type designation if material number is not known

06

Material number without "R9" for the attachment pump or type designation if material number is not known

1)Detailed information see type key

01

02

03

04

05

SY3HDFEF

1X

/

+

+

01

Three-way pump

SY3HDFEF

02

Component series 10 ... 19 (10 ... 19: unchanged installation and connection dimensions)

1X

03

Material number without "R9" for the main pump or type designation if material number is not known

04

Material number without "R9" for the attachment pump or type designation if material number is not known

05

Material number without "R9" for the attachment pump or type designation if material number is not known

Example of name plate (single pump)

1

Material short text

2

Production order number

3

Designation of origin

4

Fabrication number

5

Word mark

6

Material number, serial number underneath

7

Date of production

8

Plant

9

Indication of direction of rotation

10

Production location

11

QR code

Notice:

Für Rückfragen zum Regelsystem sind Material-Nummer, Fertigungsauftragsnummer, Seriennummer und Fertigungsdatum notwendig.

Technical data

mechanic and hydraulic

Size

4071125180250355

Displacement

cm³

4071125180250355

Maximum speed 1)

Vg max

rpm

26002200180019001700

Vg max and HFC fluids

rpm

-220018001500

Minimum speed 2)

rpm

200

Maximum flow (displacement)

at n0 and Vg max

l/min

104156225324475604

with nE = 1500 min-1 and Vg max

l/min

60107186270375533

Maximum power (Δp = 350 bar)

at n0 and Vg max

kW

6191131189277352

with nE = 1500 min-1 and Vg max

kW

3562109158219311

Maximum torque (Δp = 350 bar)

Nm

223395696100213911976

Maximum drive torque

Fitting key

Nm

3807001392140023003557

Splined shaft "S" overall torque

Nm

4467901392200427823952

Maximum through-drive torque

Nm

223395696100213911976

Drive shaft load

Maximum axial force

N

6008001000140018002000

Maximum radial force 3)

N

10001200160020002200

Weight (without filling quantity)

kg

395388102184207

Moment of inertia around drive axis

kg·m²

0.00490.01210.030.0550.09590.19

Filling quantity of the housing

l

22.554108

Maximum operating pressure 4)

bar

350

Operating pressure, min. (without load)

bar

≥ 20

Admissible inlet pressure

bar

0.8 ... 30

Hydraulic fluid

Mineral oil (HL, HLP) according to DIN 51524; HFC optional

Hydraulic fluid temperature range

°C

-20 … +70

Maximum admissible degree of contamination of the hydraulic fluid, cleanliness class according to ISO 4406 (c)

Class 18/16/13 (for particle size ≤ 4/6/14 μm)
1)The values apply at an absolute pressure of 1 bar at suction opening S. With a reduction of the displacement or an increase in the inlet pressure, the speed can be increased accordingto the following characteristic curve.
With a reduced inlet pressure, the speed is to be reduced.
2)Does not apply to HFC fluid, formula for determination of the minimum speed see below
3)In case of higher radial forces, please consult us. Not applicable for use of HFC fluids.
4)When using HFC fluids, also see data sheet 92053.

Determination of the minimum speed at HFC hydraulic fluid

Size

4071125180250355

Speed

n0

rpm

-750850600550450

Admissible load

Example 1:

The axial piston variable displacement pump A4VSO125 may be operated at ν = 16 mm2/s

as of n = 1328 rpm with nominal load

Example 2:

For the axial piston variable displacement pump A4VSO250, the admissible load with

n = 500 rpm and 10 mm2/s

x = 10/25*500/550 = 0.364 (= 127 bar at Vg max)

electrical

Power supply 1)

Nominal voltage

VDC

24

Lower limit value

VDC

18

Upper limit value

VDC

36

Maximum residual ripple

Vpp

2.5

Maximum power consumption

W

40

Required fuse protection, external

4, time-lag

AD/DA resolution

Analog inputs

bits

12

Analog outputs 2)

bits

10

Actual pressure value input XH4, pin 10 and 11

Analog voltage

V

0 … 10

Analog current 3)

mA

0 … 20

Ambient temperature range at the pump

°C

​0 … +60

Storage temperature range (pump + electronics)

°C

​0 … +40

Electronics design

Integrated at pilot control valve (OBE)

Protection class according to EN 60529

Pump incl. pilot control valve

IP65 with mounted and locked plug-in connectors
1)Supply voltage is used directly for sensor connections X2M1, X2M2 and X8M (no internal voltage limitation)
2)The outputs are parameterizable. For the condition as supplied, see "Electrical connection".
3)With configuration on current input: Maximum input current 30 mA

Notice:

For information on the environment simulation testing for the areas EMC (electromagnetic compatibility), climate and mechanical load see data sheet 29016 (declarations on environmental compatibility).

Bearing flushing

With the following operating conditions, bearing flushing is necessary for safe continuous operation:

  • Applications with special fluids (not mineral fluids) due to limited lubricity and tight operating temperature range
  • Operation with boundary conditions of temperature and viscosity with mineral oil operation

With vertical installation (drive shaft upwards), bearing flushing is recommended for lubrication of the front bearing and the shaft seal ring.

The bearing is flushed using port "U" in the area of the front flange of the variable displacement pump. The flushing fluid flows through the front bearing and exits with the pump leakage at the leakage connection.

Recommended flushing quantity

Size

4071125180250355

Recommended flushing quantity

l/min

34571015

The specified flushing quantities result in a pressure differential between port "U” (including fitting) and the leakage chamber of approx. 2 bar (series 1) and approx. 3 bar (series 3).

When using the external bearing flushing, the throttle screw in port U has to be screwed-in to the stop.

Leakage pressure

The admissible leakage pressure (housing pressure) depends on the speed (see diagram).

Maximum leakage pressure (housing pressure): 4 bar absolute

These specifications are guidelines; under special operating conditions, a limitation may become necessary.

Direction of flow: S → B

Control loop quality

Swivel angle control

Pressure control

1)

Linearity tolerance

≤1.0 %

≤1.5 % (≤1.0 %) 2)

Temperature error

≤0.5 % / 10 K

≤0.5 % / 10 K

Hysteresis

≤0.2 %

≤0.2 %

Repetition accuracy

≤0.2 %

≤0.2 %

1)Without considering the pump pulsation.
2)Using the integrated calibration function.

Notices:

  • ●The specified values are only valid when using the system-related components (see "Accessories").
  • At pressures <20 bar, higher tolerances have to be anticipated due to lower actuating forces.

Through-drives : Drive and through-drive torques

Maximum drive and through-drive torques

Size

40

71

125

180

250

355

Splined shaft

Total drive torque at the shaft of pump 1 (pump 1 + pump 2)

TGes max

Nm

446

790

1392

2004

2782

3952

Through-drive torque A

TD1 max

Nm

223

395

696

1002

1391

1976

TD2 max

Nm

223

395

696

1002

1391

1976

Through-drive torque B

TD1 max

Nm

223

395

696

1002

1391

1976

TD2 max

Nm

223

395

696

1002

1391

1976

Fitting key

Total drive torque at the shaft of pump 1 (pump 1 + pump 2)

TGes max

Nm

380

700

1392

1400

2300

3557

Through-drive torque A

TD1 max

Nm

223

395

696

1002

1391

1976

TD2 max

Nm

157

305

696

398

909

1581

Through-drive torque B

TD1 max

Nm

157

305

696

398

909

1581

TD2 max

Nm

223

395

696

1002

1391

1976

Distribution of through-drive torques

Mass torque (relates to mounting flange of main pump)

Size

40

71

125

180

250

355

Maximum mass torque

Tm zul.

Nm

1800

2000

4200

4200

9300

9300

Maximum mass torque with dynamic mass acceleration of 10 g = 98.1 m/s2

Tm zul.

Nm

180

200

420

420

930

930

Weight (SYHDFE or A4VSO...DR)

m

kg

39

53

88

102

184

207

Distance of the center of gravity

l1

mm

120

140

170

180

210

220

Tm​ ​[Nm]

Maximum mass torque

m1, m2 ​[kg]

Weight of the pump

l1, l2 ​[mm]

Distance of the center of gravity

(For applications outside these values, please consult us!)

Diagrams/characteristic curves

Transition function for pressure command value step (control spool version "A")

T95% in ms with a connected hydraulic fluid volume (lines and actuators)

Hydraulic fluid volume in l

T95% in ms

<​5

150

5 … 10

200

15 … 25

250

Notices:

  • For pressures up to 40 bar, the values of the response times are greater.
  • The specified curve shapes and control times refer to a drive speed of 1500 rpm and are only reached with an optimization of the pressure controller.

Transition function with swivel angle command value step (control spool version "A")

Size 40, 71 (p = 100 bar)

Size 125 (p = 100 bar)

Size 180 (p = 100 bar)

Size 250 (p = 100 bar)

Size 355 (p = 100 bar)

Symbols/Circuit diagrams

Schematic diagram : Actuating system supplied internally

S

Suction port

K1, K2

Flushing port

T

Fluid drain

MB

Measuring port operating pressure (M14x1,5)

MS

Measuring port suction pressure

M1, M2

Measuring port control chamber pressure

R(L)

Fluid filling + bleeding (leakage connection)

U

Flushing port

B

Pressure port

B1

2nd Pressure port/additional port

MB1

Measuring port operating pressure
NG250/355: G1/4
NG 40/71/125/180: Blind flange attached to B1 with pressure measuring port G1/4

Using the pressure transducer HM 20-2X/…C13

  • Installation in MB or MB1 (pump) in connection with electronic version for actual pressure value input "F"
  • For attachment of an HM20-2X/315-F-C13-0.5 in MB, an adapter from M14 x 1.5 to G1/4 (material no. R900695665) is required.
  • Due to the installation position, the HM20 cable version cannot be used for all sizes without restrictions (check use with M12 extension cable).

Using an external pressure transducer

Installation in line B (preferably close to the actuator) and electrical connection via central connection X1

Notice:

The actual pressure value at port B must not be less than 10 bar for more than 10 minutes (lubrication).

Schematic diagram : Actuating system supplied externally

1)Maximum pressure limitation must be provided by the customer.

S

Suction port

K1, K2

Flushing port

T

Fluid drain

MB

Measuring port operating pressure (M14x1,5)

MS

Measuring port suction pressure

M1, M2

Measuring port control chamber pressure

R(L)

Fluid filling + bleeding (leakage connection)

U

Flushing port

B

Pressure port

B1

2nd Pressure port/additional port

MB1

Measuring port operating pressure
NG250/355: G1/4
NG 40/71/125/180: Blind flange attached to B1 with pressure measuring port G1/4

Z

External pilot oil pressure
(DIN 3852 M14 x 1.5; 12 deep (pmax(abs) = 50 bar)

Notes on external supply:

  • In the case of an actuating system with external supply, the pump adjustment will - in case of voltage failure - not switch to zero stroke but to the negative stop (displacement of 100 % flow from the system to the tank).
  • With an active fault message, it is imperative that the machine control reacts (e. g. switching off the drive motor of the pump, interrupting the external supply of the actuating system).
  • The command values for pressure and flow must always be greater than zero (pcommand ≥ 3 bar, αcommand ≥ 5 %) as due to drift or tolerances, there is no exact "zero" pressure or "zero" swivel angle. Under unfavorable conditions, smaller command value presettings can lead to cavitation.
  • The actual pressure value must not be less than 10 bar for more than 10 minutes (lubrication).
  • Port Z must be connected to tank level in case of non-use. Closing is not admissible.

Electrical connection

XH1, central connection

Assignment of connector or mating connector and cable set

Pin

Signal

Description

Signal direction

Type of signal

Allocation in the cable set (accessories)

A

+ UB

Voltage supply

IN

24 VDC

brown

Line 7 x 0.75 mm2 shielded (one end of the shield must be connected to the control)

B

0 V = L0

Reference potential for the voltage supply

yellow

PE

Earth

Earthing connection for the electronics

green/yellow

C

Do not use

green

D

AI1

Analog input 1 (freely-configurable)

IN

analog ±10 V
or 0 ... 20 mA

blue

E

M0

Reference potential for analog signals

gray

F

AO1

Analog input 1 (freely-configurable)

OUT

analog ±10 V
or 0 ... 20 mA

white

X7E1 and X7E2, Connector pin assignment for Ethernet interface (coding D), M12, 4-pole, socket

Pin

Assignment

1

TxD +

2

RxD +

3

TxD –

4

RxD –

5

Not assigned

X2N, analog configurable sensor interface (coding A), M12, 5-pole, socket

Pin

Assignment

1

+ 24 V voltage output (sensor supply)

1)​

2

Analog input voltage 2 (0 … 10 V)

3

GND

4

Analog input voltage 4 (0 … 10 V)

5

Analog input voltage 3 (0 … 10 V)

1)Maximum load capacity 3 x 25 mA, voltage output same as voltage supply connected to input XH1.

Notices:

  • X8A, actual swivel angle value input (coding A), M12, 5-pole, socket M12
  • Mating connectors, separate order, see "Accessories"

LED displays

LED

Interface

Sercos

EtherNet/IP

EtherCAT

PROFINET RT

VARAN

MS

Electronic module

Module Status

Module Status

Module Status

Module Status

Module Status

NS

S

Network status and others

Network status and others

Network status and others

Network status and others

L1

X7E1

Link and others

Link and others

Link/Activity

Link and others

Link and others

S1

Activity and others

Activity and others

not used

Activity and others

Activity and others

L2

X7E2

Link and others

Link and others

Link/Activity

Link and others

not used

S2

Activity and others

Activity and others

not used

Activity and others

not used

PWR

XH1

Power

Power

Power

Power

Power

Displays of the Status LEDs

Module status

(LED MS)

Display status

Off

No voltage supply

Green-red, flashing

Initialization

Green, flashing

Drive ready for operation

Green

Drive active

Orange, flashing

Warning

Red, flashing

Error

Green, rapidly flashing

Firmware must be loaded

Power LED

(LED PWR)

Display status

Off

No voltage supply

Green

Operation

Link-LED

(LED L1)

Display status

Permanently lit

Cable plugged in, connection established

Activity-LED

(LED S1)

Display status

Flashing

Data sent/received

Notices:

  • For the connection to the M12 sockets, we recommend using self-locking mating connectors.
  • Module status LED MS relates to the electronics module.
  • The network status LED NS indicates the status of the control communication, see application description 30338-FK.
  • LEDs L1, S1, L2 and S2 relate to interfaces "X7E1" and "X7E2"
  • For a detailed description of the diagnosis LEDs, please refer to the functional description "Rexroth HydraulicDrive HDx".
  • Function is only available after start-up of the electronics.

Dimensions

Installation orientation "0"

Dimensions in mm

1

Port Z (for version SYHDFE.-1X...0576)

(DIN 3852 M14 x 1.5; 12 deep (pmax(abs) = 50 bar)

5

Space required for the connection line

Size

A1

A2

A3

A4a

A4b

A5

A6

A7

A8

A9

A10

A12

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

402128012713016710412516015227348100
7122992.514114916712714018015254375100
125264112.517117716714716020020310444100
18026411617117716714716020020318444100
25031214420721216717922428024380506100
35531214420721216717922428024393598100

Notice:

Dimensions base pump (axial piston variable displacement pump A4VSO) see data sheet 92050.

Installation orientation "1"

Dimensions in mm

1

Port Z (for version SYHDFE.-1X...0576)

(DIN 3852 M14 x 1.5; 12 deep (pmax(abs) = 50 bar)

5

Space required for the connection line

Size

A1

A2

A3

A4a

A4b

A5

A6

A7

A8

A9

A10

A12

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

402128024113016710412516015227280100
7125092.525514916712714018015254310100
125264112.528517716714716020020310368100
18026411628517716714716020020318392100
25031214432121216717922428024380455100
35531214432121216717922428024393487100

Notice:

Dimensions base pump (axial piston variable displacement pump A4VSO) see data sheet 92050.

Shaft ends

Size

Shaft Ø

= P 1)

= Z 2)

mm

4032AS 10 x 8 x 56W 32 x 2 x 14 x 9 g
7140AS 12 x8 x 68W 40 x 2 x 18 x 9 g
12550AS 14 x 9 x 80W 50 x 2 x 24 x 9 g
18050AS 14 x 9 x 80W 50 x 2 x 24 x 9 g
25060AS 18 x 11 x 100W 60 x 2 x 28 x 9 g
35570AS 20 x 12 x 100W 70 x 3 x 22 x 9 g
1)Cylindrical with fitting key DIN 6885
2)Splined shaft profile DIN 5480

Through-drives

"K99"

With through-drive shaft, without hub, without intermediate flange, closed operationally safe with end cover.

Dimensions in mm

1

Up to pump mounting face

2

Splined shaft profile DIN 5480

Size

A1

A2

A4

A5

A6

A7

A8

A9

A10

A11

⌀A12

⌀A13

⌀A14

⌀A15

A16

A17

Splined shaft profile DIN 5480

1) Seal ring for later attachment
(separate order)

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

4026328051.3± 1M12; 25 mm deep37+ 0.237+ 0.201892.3+ 0.1118H7105g697.6- 0.4524414W25 x 1,25 x 18 x 9 g99 x 3
7129131048± 1M12; 25 mm deep42.3+ 0.1545+ 0.1515.41892.7+ 0.1130H7116g6106.4- 0.4633816W30 x 1,25 x 22 x 9 g110,72 x 3,53

Notice:

Left view, drawing without cover.

"U99"

With through-drive shaft, without hub, without intermediate flange, closed operationally safe with end cover.

Dimensions in mm

1

Up to pump mounting face

2

Splined shaft profile DIN 5480

3

Only NG250 and 355

Size

A1

A2

A4

A5

A6

A7

A8

A9

ØA10

A12

A13

ØA14

ØA15

A16

A17

A18

Splined shaft profile DIN 5480

1) Seal ring for later attachment
(separate order)

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

mm

12534736849.7± 1M14; 15 deep33.2+ 0.15
0
M12; 18 deep--
-
79.2+ 0.15
0
118H7
92.8+ 0.2
0
121+ 0.1
+ 0
704622--
-
W35 x 1.25 x 26 x 9 g118 x 2
18037139249.7± 1M14; 15 deep33.2+ 0.15
0
M12; 18 deep--
-
79.2+ 0.15
0
118H7
92.8+ 0.2
0
121+ 0.1
+ 0
704625--
-
W35 x 1.25 x 26 x 9 g118 x 2
25043145561.4± 1M20; 22 deep44.5+ 0.15
0
M10; 15 deep58.15+ 0.15
0
86.2+ 0.15
0
160H7
92.8+ 0.2
0
163+ 0.1
+ 0
876430.586.2+ 0.15
0
W42 x 1.25 x 32 x 9 g160 x 2
35546048761.4± 1M20; 22 deep44.5+ 0.15
0
M10; 15 deep58.15+ 0.15
0
86.2+ 0.15
0
160H7
92.8+ 0.2
0
163+ 0.1
+ 0
87643486.2+ 0.15
0
W42 x 1.25 x 32 x 9 g160 x 2

Notice:

Left view, drawing without cover.

"UB3"

Flange ISO 3019-2 100, 2-hole Hub for splined shaft, 22-4 SAE B, 7/8˝, 16/32 DP; 13T 2) for attachment of an A10VSO 28/31 splined shaft "S" (see data sheet 92711)

Dimensions in mm

1)2 mounting screws and seal ring included in the scope of delivery.
2)According to ANSI B92.1a-1976, 30° pressure angle, flat root, side fit, tolerance class 5

1

Up to pump mounting face

Size

A1

A3

A4

A5

A6

mm

mm

mm

mm

12536920.524.910M12
18039320.524.910M12

Notices:

  • Before determining the design, please request a binding installation drawing.
  • Thread according to DIN 13 (for maximum tightening torques, see "Installation").

"UB4"

Flange ISO 3019-2 100, 2-hole

Hub for splined shaft, 25-4 SAE B-B, 1˝, 16/32 DP; 15T 2) for attachment of an A10VSO 45/31 splined shaft "S" (see data sheet 92711)

Dimensions in mm

1)2 mounting screws and seal ring included in the scope of delivery.
2)According to ANSI B92.1a-1976, 30° pressure angle, flat root, side fit, tolerance class 5

1

Up to pump mounting face

Size

A1

A3

A4

A5

A6

mm

mm

mm

mm

12536918.929.510M12
18039318.929.510M12
25045320.929.510M12
35548220.929.510M12

Notices:

  • Before determining the design, please request a binding installation drawing.
  • Thread according to DIN 13 (for maximum tightening torques, see "Installation").

"UB8"

Flange ISO 3019-2 160, 4-hole

Hub for splined shaft, 32-4 SAE C, 1 1/4˝, 12/24 DP; 14T 2) for attachment of an A10VSO 71/32 splined shaft "S" (see data sheet 92714)

Dimensions in mm

1)2 mounting screws and seal ring included in the scope of delivery.
2)According to ANSI B92.1a-1976, 30° pressure angle, flat root, side fit, tolerance class 5

1

Up to pump mounting face

Size

A1

A3

A4

A5

A6

mm

mm

mm

mm

25045320.9389M16

Notices:

  • Before determining the design, please request a binding installation drawing.
  • Thread according to DIN 13 (for maximum tightening torques, see "Installation").

"UB7"

Flange ISO 3019-2 180, 4-hole

Hub for splined shaft, 44-4 SAE D, 1 3/4˝, 8/16 DP; 13T 2) for attachment of an A10VSO 140/31(32) splined shaft "S" (see data sheet 92711, 92714)

Dimensions in mm

1)2 mounting screws and seal ring included in the scope of delivery.
2)According to ANSI B92.1a-1976, 30° pressure angle, flat root, side fit, tolerance class 5

1

Up to pump mounting face

Size

A1

A3

A4

A5

A6

mm

mm

mm

mm

18040610.6629M16
25045310.6649M16
35548210.649M16

Notices:

  • Before determining the design, please request a binding installation drawing.
  • Thread according to DIN 13 (for maximum tightening torques, see "Installation").

"U34"

Flange ISO 3019-2 160, 4-hole

Hub according to DIN 5480 N50 x 2 x 24 x 8H for attachment of an A4VSO/G 125 or 180 splined shaft

Dimensions in mm

1)2 mounting screws and seal ring included in the scope of delivery.

1

Up to pump mounting face

Size

A1

A3

A4

A5

A6

mm

mm

mm

mm

12536912.551.69M16
18039312.551.69M16
25045312.5549M16
35548212.5549M16

Notices:

  • Before determining the design, please request a binding installation drawing.
  • Thread according to DIN 13 (for maximum tightening torques, see "Installation").

"U35"

Flange ISO 3019-2 224, 4-hole

Hub according to DIN 5480 N60 x 2 x 28 x 8H for attachment of an A4VSO/G or A4CSG 250 splined shaft

Dimensions in mm

1)2 mounting screws and seal ring included in the scope of delivery.

1

Up to pump mounting face

Size

A1

A3

A4

A5

A6

mm

mm

mm

mm

25046912.6759M20
35549812.6759M20

Notices:

  • Before determining the design, please request a binding installation drawing.
  • Thread according to DIN 13 (for maximum tightening torques, see "Installation").

"U77"

Flange ISO 3019-2 224, 4-hole

Hub according to DIN 5480 N70 x 3 x 22 x 8H for attachment of an A4VSO/G or A4CSG 355 splined shaft

Dimensions in mm

1)2 mounting screws and seal ring included in the scope of delivery.

1

Up to pump mounting face

Size

A1

A3

A4

A5

A6

mm

mm

mm

mm

35549812.5759M20

Notices:

  • Before determining the design, please request a binding installation drawing.
  • Thread according to DIN 13 (for maximum tightening torques, see "Installation").

"U01"

Flange ISO 3019-1 82-2 (SAE A)

Hub for splined shaft, 16-4 SAE A, 5/8˝, 16/32 DP; 9T 2) for attachment of an external gear pump AZ-PF-1X-004 ... 022 (see data sheet 10089); recommendation: special version of the gear pumps, please contact us.

Dimensions in mm

1)2 mounting screws and seal ring included in the scope of delivery.
2)According to ANSI B92.1a-1976, 30° pressure angle, flat root, side fit, tolerance class 5

1

Up to pump mounting face

Size

A1

A3

A4

A5

A6

mm

mm

mm

mm

1253691619.413M10
1803931619.413M10
2504531619.413M10
3554821619.413M10

Notices:

  • Before determining the design, please request a binding installation drawing.
  • Thread according to DIN 13 (for maximum tightening torques, see "Installation").

"U68"

Flange ISO 3019-1 101-2 (SAE B)

Hub for splined shaft 22-4 SAE B, 7/8˝, 16/32 DP; 13T 2) for attachment of an external gear pump AZ-PN-1X020 ... 032 (see data sheet 10091) or A10VO 28/31 and 52(53); splined shaft "S" (see data sheet 92701 and 92703); recommendation: special version of the gear pumps, please contact us.

Dimensions in mm

1)2 mounting screws and seal ring included in the scope of delivery.
2)According to ANSI B92.1a-1976, 30° pressure angle, flat root, side fit, tolerance class 5

1

Up to pump mounting face

2

Only NG125 and 180

Size

A1

A3

A4

A5

A6

mm

mm

mm

mm

125369282513M12
180393282513M12
25045319.523.113M12
35548219.523.113M12

Notices:

  • Before determining the design, please request a binding installation drawing.
  • Thread according to DIN 13 (for maximum tightening torques, see "Installation").

"U04"

Flange ISO 3019-1 101-2 (SAE B)

Hub for splined shaft 25-4 SAE B-B, 1˝, 16/32 DP; 15T 2) for attachment of an A10VO 45/31 and 52 (53), splined shaft "S" (see data sheet 92701 and 92703) or an internal gear pump PGH4 (see data sheet 10223)

Dimensions in mm

1)2 mounting screws and seal ring included in the scope of delivery.
2)According to ANSI B92.1a-1976, 30° pressure angle, flat root, side fit, tolerance class 5

1

Up to pump mounting face

2

Only NG125 and 180

Size

A1

A3

A4

A5

A6

mm

mm

mm

mm

12536918.929.413M12
18039318.929.413M12
25045318.929.413M12
35548218.929.413M12

Notices:

  • Before determining the design, please request a binding installation drawing.
  • Thread according to DIN 13 (for maximum tightening torques, see "Installation").

"U24"

Flange ISO 3019-1 127-2 (SAE C)

Hub for splined shaft 38-4 SAE C-C, 1 1/2˝, 12/24 DP; 17T 2) for attachment of an A10VO 100/31 splined shaft, "S" (see data sheet 92701) or A10VO 85/52(53), splined shaft "S" (see data sheet 92703) or an internal gear pump PGH5 (see data sheet 10223)

Dimensions in mm

1)2 mounting screws and seal ring included in the scope of delivery.
2)According to ANSI B92.1a-1976, 30° pressure angle, flat root, side fit, tolerance class 5

1

Up to pump mounting face

Size

A1

A3

A4

A5

A6

mm

mm

mm

mm

12536910.45013M16
18039310.45013M16
25045312.45513M16
35548212.45513M16

Notices:

  • Before determining the design, please request a binding installation drawing.
  • Thread according to DIN 13 (for maximum tightening torques, see "Installation").

Project planning information

  • Command values may only be switched via relays with gold-plated contacts (low voltage, low currents)
  • Always shield command and actual value cables.
  • The distance to aerial lines or radios must be at least 1 m.
  • Do not lay signal lines close to power lines.
  • Amending notes on the SYHDFE control system can be found in the operating instructions (See section “Further information about this control system”).

Through-drives : Size 40 … 71

The control systems of size 40 … 71 are partly supplied with through-drive "K99".

Their advantage is that the through-drive can be subsequently modified. By simply exchanging the intermediate flange and the hub, the through-drive can be adjusted to the on-site requirements.

The assemblies as exchange kits can be ordered separately, see "Accessories for through-drives" as well as data sheet 95581.

Small centering diameters are directly worked into the pump subplate. Subsequent modification is not possible. In this connection, observe the "Type codes" as well as "Accessories for through-drives". Hubs for through-drives can be ordered separately.

Through-drives : Size 125 … 355

The control systems of size 125 … 355 are supplied with universal through-drives "U99".

Their advantage is that the through-drive can be subsequently modified. By simply exchanging the intermediate flange and the hub, the through-drive can be adjusted to the on-site requirements.

The assemblies as exchange kits can be ordered separately, see "Accessories for through-drives" as well as data sheet 95581.

Mounting

Tightening torques

  • The tightening torques specified in this data sheet are maximum values and must not be exceeded (maximum values for screw-in threads). Manufacturer's specifications regarding the maximum admissible tightening torques of the fittings used are to be
  • For mounting screws according to DIN 13, we recommend checking the tightening torque case by case accordingto VDI 2230, version 2003.

Accessories

Through-drives

The following conditions apply to the attachment pumps listed in the table:

  • Internal gear pump PGH with shaft "R", flange "U2", see data sheet 1022
  • Internal gear pump PGF3 with shaft "J", flange "U2", see data sheet 10213
  • External gear pump AZPF with shaft "R", front cover "R", see data sheet 10089

Observe that the through-drive of the main pump and the flange of the attachment pump (see type key pump) are identical. Check in the current data sheet of the gear pump whether the shaft ends have the specified dimensions.

Attachment kits for axial piston variable displacement pumps and SYHDFE control systems

Components universal through-drive

"U99"

Main pump SYHDFE.-1X

Attachment pump

NG125
NG180

NG250
NG355

Size and type

Through-drive

Centering

Hub

Flange designation

Mounting kit

R902447035

R902447037

NG18

SYDFE.-2X
A10VSO / BR31

Shaft "S" or "R"

U52
82,55 mm
3/4″

SAE
J744 82-1
(A-B)

Flange kit

R902446836

R902446850

Hub

R902446823

R902446843

Mounting kit

R902446996

R902446998

NG28

UB3
100 mm
7/8″

ISO 3019-2
100B2HW

Flange kit

R902446808

R902446809

Hub

R902446824

R902446844

Mounting kit

R902447001

R902447003

NG45

UB4
100 mm
1″

ISO 3019-2
100B2HW

Flange kit

R902446808

R902446809

Hub

R902446825

R902446845

Mounting kit

Upon request

Upon request

NG40

SYDFE.-3X
A10VSO / BR32

Shaft "S" or "R"

UE1
125 mm
1″

ISO 3019-2
125B4HW

Flange kit

Upon request

R902446813

Hub

R902446825

R902446845

Mounting kit

R902447014

R902447016

NG71

UB8
160 mm
1 1/4″

ISO 3019-2
160B4HW

Flange kit

R902446816

R902446817

Hub

R902446826

R902443227

Mounting kit

R902447021

R902447022

NG100

UB9
180 mm
1 1/2″

ISO 3019-2
180B4HW

Flange kit

R902446818

R902446820

Hub

R910943555

R910921237

Mounting kit

R902447025

R902447026

NG140

UB7
180 mm
1 3/4″

ISO 3019-2
180B4HW

Flange kit

R902446818

R902446820

Hub

R910904588

R902446849

Mounting kit

R902447010

R902447011

NG40

SYHDFE-1X
A4VSO / BR30

Shaft "Z"

U31
125 mm
W 32 x 2 x 14 x 9 g

ISO 3019-2
125B4HW

Flange kit

R902446812

R902446813

Hub

R902446828

R902446846

Mounting kit

R902447012

R902447013

NG71

U33
140 mm
W 40 x 2 x 18 x 9 g

ISO 3019-2
140B4HW

Flange kit

R902446814

R902446815

Hub

R902491155

R902446847

Mounting kit

R902447019

R902447020

NG125
NG180

U34
160 mm
W 50 x 2 x 24 x 9 g

ISO 3019-2
160B4HW

Flange kit

R902446816

R902446817

Hub

R902446848

R902446830

Mounting kit

R902447028

NG250

U35
224 mm
W 60 x 2 x 28 x 9 g

ISO 3019-2
224B4HW

Flange kit

R902446822

Hub

R910902972

Mounting kit

R902447029

NG355

U77
224 mm
W 70 x 3 x 22 x 9 g

ISO 3019-2
224B4HW

Flange kit

R902446822

Hub

R910941327

Mounting kit

R902447030

R902447032

PGF 2, PGH 2, PGH 3, AZPF

U01
82,55 mm
5/8″

SAE J744
82-2(A-B)

Flange kit

R902446836

R902446850

Hub

R902446831

R902497505

Mounting kit

R902447040

R902447042

PGF 3

U68
101,6 mm
7/8″

SAE J744
101-2(B

Flange kit

R902446837

R902446851

Hub

R902446824

R902446844

Mounting kit

R902447045

R902447047

PGH 4

U04
101,6 mm
1″

SAE J744
101-2(B)

Flange kit

R902446837

R902446851

Hub

R902446825

R902446845

Mounting kit

R902447052

R902447053

PGH 5

U24
127 mm
1 1/2″

SAE J744
127-2(B)

Flange kit

R902446838

R902446852

Hub

R910943555

R910921237

Attachment kits for axial piston variable displacement pumps and SYHDFE control systems

Components universal through-drive

"K99"

Main pump SYHDFE.-1X

Attachment pump

NG40

NG71

Size and type

Through-drive

Centering

Hub

Flange designation

Mounting kit

Upon request

R902546965 1)

NG18

SYDFE.-2X
A10VSO / BR31

Shaft "S" or "R"

K52
82,55 mm
3/4″

ISO 3019-1
82-2

Mounting kit

R902488855

R902566875

NG28

KB3
100 mm
7/8″

ISO 3019-2
100B2HW

Mounting kit

Upon request

R902450062

NG45

KB4
100 mm
1″

ISO 3019-2
100B2HW

Mounting kit

R902543215

NG45

SYDFE.-3X
A10VSO / BR32

Shaft "S" or "R"

KE1
125 mm
1″

ISO 3019-2
125B4HW

Mounting kit

R902543416

NG71

KB8
160 mm
1 1/4″

ISO 3019-2
160B4HW

Mounting kit

R902425118

R910904879

NG40

SYHDFE-1X
A4VSO / BR10

Shaft "Z"

K31
125 mm
W 32 x 2 x 14 x 9 g

ISO 3019-2
125B4HW

Mounting kit

R902403972

NG71

K33
140 mm
W 40 x 2 x 18 x 9 g

ISO 3019-2
140B4HW

1)Only with through-drive "K01"

Attachment kits for axial piston variable displacement pumps and SYHDFE control systems

Components through-drive

Main pump SYHDFE.-1X

Attachment pump

NG40

NG71

Size and type

Through-drive

Centering

Hub

Flange designation

Hub

Upon request

Upon request

PGF 2, PGH 2, PGH 3, AZPF

K01
82,55 mm
5/8″

ISO 3019-1
82-2

Notice:

The order numbers for the combination of pumps are contained in the table and in data sheet 95581.

Hubs for standard electric motor coupling

Coupling with gear rim for ambient temperatures up to 80 °C, e.g. for motor assemblies with IM V1 motor.

Motor

SYHDFE.-1X

Shaft "Z"

Frame size/characteristic

Shaft diameter

NG71

Shaft

W40 x 2 x 18 x 9 g

NG125/180

Shaft

W50 x 2 x 24 x 9 g

NG250

Shaft

W60 x 2 x 28 x 9 g

NG355

Shaft

W70 x 3 x 22 x 9 g

225/0

60

R900026054

R900026055

250/0

65

R900026058

R900026059

280/0

75

R900026062

R900026063

R900714636

315/0

80

R901037250

R901076760

R900088584 1)

R900210961 1)

315/1

80

R900026068

R900783295

R900210960

1)Up to 40 °C

Accessories

Material number

Data sheet

Mating connector 6-pole for central connection XH1 without cable (assembly kit)

R900021267

08006

Mating connector 6-pole for central connection XH1 with cable set 3 m

R901420483

08006

Mating connector 6-pole for central connection XH1 with cable set 5 m

R901420491

08006

Mating connector 6-pole for central connection XH1 with cable set 10 m

R901420496

08006

Pressure transducer HM 20-2X, measurement range 315 bar (4 ... 20 mA)

R901342029

30272

Pressure transducer HM 20-2X, measurement range 315 bar (0.1 ... 10 V)

R901342030

30272

Pressure transducer HM 20-2X, measurement range 315 bar (0.5 ... 5 V) with 0,5 m cable

R901342038

30272

Ethernet connection cable M12 to RJ45 (connection X7E1 & X7E2), additional information type designation RKB0044

R911343806

Commissioning software IndraWorks DS from version 14V14

Mating connectors for valves with round connector, 11-pole + PE

12P N11

Mating connectors for valves with round connector, 11-pole + PE

12P N11

  • For valves with round connector according to EN 175201-804, 11-pole + PE

Mating connectors for valves with round connector, 11-pole + PE, shielded, with assembled connection line

12P N11 +

Mating connectors for valves with round connector, 11-pole + PE, shielded, with assembled connection line

12P N11 +

  • For valves with round connector according to EN 175201-804, 11-pole + PE

Proportional directional valves direct operated, with electrical position feedback as pilot control valve for control systems
SY(H)DFE.

VT-DFP.

Proportional directional valves direct operated, with electrical position feedback as pilot control valve for control systems
SY(H)DFE.

VT-DFP.

  • Component series 2X, 1X

Ordering codes

Downloads

SYDFEF Serie 2X, 3X, SYHDFEF Serie 1X, Druck- und Förderstrom-Regelsystem
Manual | RD30013-B/08.2020 | 2020-08-01 | German | PDF | 2.9MB

Product Groups: Electro-hydraulic control systems
Betriebsanleitung
SYDFEF series 2X, 3X, SYHDFEF series 1X, pressure and flow control system
Manual | RE30013-B/08.2020 | 2020-08-01 | English | PDF | 2.9MB

Product Groups: Electro-hydraulic control systems
Druck- und Förderstrom-Regelsystem
Data Sheet | RD30035 | 2021-10-01 | German | PDF | 1.7MB

Product Groups: Electro-hydraulic control systems
Typ SYHDFEE, SYHDFED, SYHDFEF
Pressure and flow control system
Data Sheet | RE30035 | 2021-10-01 | English, United States | PDF | 1.7MB

Product Groups: Electro-hydraulic control systems
Type SYHDFEE, SYHDFED, SYHDFEF
Rexroth HydraulicDrive, HDx-20 pump control
Manual | RE30237-Z | 2020-10-07 | English | PDF | 6.5MB

Product Groups: Axis control
Rexroth HydraulicDrive HDS-16, HDx-17 to HDx-20 Parameters
Reference Book | RE30330-PA | 2020-04-01 | English | PDF | 12.6MB

Product Groups: Axis control
Reference Book
Rexroth HydraulicDrive HDS-16, HDx-17 bis HDx-20 Parameter
Reference Book | RD30330-PA | 2020-04-01 | German | PDF | 12.7MB

Product Groups: Axis control
Referenz
Rexroth HydraulicDrive HDx-20VRS Firmware for drive controllers
Release Note | RE30330-RN | 2019-06-06 | English | PDF | 2.9MB

Product Groups: Axis control
Firmware Release Notes
Rexroth HydraulicDrive HDx-20VRS Firmware für Antriebsregelgeräte
Release Note | RD30330-RN | 2019-06-06 | German | PDF | 3MB

Product Groups: Axis control
Firmware Release Notes
Rexroth HydraulicDrive HDS-16, HDx-17 to HDx-20, Diagnostic Messages
Manual | RE30330-WA | 2020-04-01 | English | PDF | 4.9MB

Product Groups: Axis control
Reference
Rexroth HydraulicDrive HDS-16, HDx-17 bis HDx-20, Diagnosen
Manual | RD30330-WA | 2020-04-01 | German | PDF | 5MB

Product Groups: Axis control
Referenz
Rexroth HydraulicDrive HDx-20 Functions
Manual | RE30338-FK | 2020-04-01 | English | PDF | 59.1MB

Product Groups: Axis control
Rexroth HydraulicDrive HDx-20 Funktionen
Manual | RD30338-FK | 2020-04-01 | German | PDF | 59.8MB

Product Groups: Axis control

Мы предлагаем следующие способы доставки товара:

Самовывоз из пункта выдачи

Самостоятельное получение заказа в пункте выдачи. Дата и время получения заранее согласуется с менеджером магазина.
Отгрузка товара юридическим лицам осуществляется только при наличии печати или правильно оформленной и заполненной доверенности, наличии паспорта получателя.


Курьерская доставка по Москве

Доставка по адресу покупателя или до пункта приема транспортной компании в г. Москве. Дата и время доставки заранее согласуется с менеджером магазина.

Доставка транспортной компанией по России

Доставка транспортной компанией по России до пункта выдачи транспортной компании или до конечного адреса покупателя. 
 

Для расчета коммерческого предложения или получения счета на поставку оборудования и программного обеспечения Bosch Rexroth оставьте заявку в форме ниже или свяжитесь с отделом продаж по телефону +7 495 137-07-02 или электронной почте sale@boschrexroth-russia.ru. Мы гарантируем оперативный ответ на ваш запрос и предоставление наилучших условий от официального поставщика Bosch Rexroth. 

Специалист по решениям Bosch Rexroth:

  • Окажет профессиональную консультацию.
  • Сообщит вашу цену на продукцию.
  • Сообщит информацию об актуальных акциях и скидках.
  • Подскажет ближайшее к вам отделение с наличием нужной продукции.
  • Согласует с вами возможную дату и время доставки.

Запрос цены или КП

Запрос цен, наличия или консультация
Пришлем актуальную информацию по ценам, скидкам, наличию товара на складе и срокам поставки
НовостиВсе новости
Bosch Rexroth открывает новые возможности в управлении машинами и подключении к IoT

Bosch Rexroth предлагает одну из самых производительных систем ЧПУ на рынке. Компания является лидером в области автоматизации и устанавливают стандарты в этой области. От датчиков и сервоприводов до революционной новой платформы, Bosch Rexroth предлагает широкий спектр решений для автоматизации. ..

16 Февраля, 2024
Bosch Rexroth и TotalEnergies объединяют свои усилия для продвижения альтернативных и экологичных гидравлических жидкостей

Bosch Rexroth и TotalEnergies (французская нефтегазовая компания) 18 декабря 2023 года подписали соглашение сотрудничестве, направленном на разработку, внедрение и маркетинг гидравлических жидкостей на водной основе, с акцентом на экологичность, огнестойкость и производительность. Данный союз отр..

11 Января, 2024
Bosch Rexroth представляет Интеллектуальный функциональный набор для обработки данных Smart Function Kit for Handling

Компания Bosch Rexroth является одним из ведущих мировых производителей и поставщиков технологий и услуг в области промышленной автоматизации. Это производитель рад представить вам свой интеллектуальный функциональный набор для обработки данных. Это инновационное оборудование, с помощью которого п..

4 Декабря, 2023
Бренд Bosch Rexroth представил миру свою разработку - оборудование IndraDrive CDB02 - BASIC для двухосевого блока управления

Bosch Rexroth, являясь ведущим производителем промышленного оборудования, не стоит на месте и разрабатывает новое оборудование. Одним из изобретений этой компании является IndraDrive CDB02 - BASIC. Это двухосевой блок управления, который предназначен для использования в различных промышленных сект..

1 Декабря, 2023
Bosch Rexroth: высокоскоростной асинхронный двигатель 1MB140 

Производитель Bosch Rexroth представил свою разработку - высокоскоростной асинхронный двигатель 1MB140. Этот продукт обладает рядом уникальных характеристик и предназначен для различных применений в промышленности. Основным назначением двигателя 1MB140 является обеспечение высокой скорости вращ..

30 Ноября, 2023
Bosch Rexroth рассказывает о характеристиках электрогидравлических насосов

Bosch Rexroth представляет электрогидравлические насосы, которые объединяют в себе преимущества электрической и гидравлической технологий. Данные насосы могут использоваться в различных отраслях промышленности, включая машиностроении, автомобильной промышленности, энергетике и других. Основная ..

29 Ноября, 2023
Bosch Rexroth представил серию высокоэффективных синхронных моментных двигателей МВТ130 

Синхронные моментные двигатели МВТ130 применяются в различных отраслях промышленности: машиностроение, автомобильной и энергетической промышленности. Это оборудование используют как дополнение к насосам, компрессорам, приводам конвейеров и другим механизмам, требующим точного управления и высокой ..

28 Ноября, 2023
Bosch Rexroth: надежные и эффективные героторные насосы подходят для решения для множества задач

Героторные насосы Bosch Rexroth — это инновационное оборудование, которое обеспечивает эффективную работу в различных областях промышленности. Они являются незаменимым компонентом в системах гидравлического привода и обеспечивают надежную и плавную работу механизмов. Принцип работы герото..

27 Ноября, 2023
Для эффективной работы гидравлических систем Bosch Rexroth представляет баллонный аккумулятор HAB2 

Баллонный аккумулятор HAB2 производства компании Bosch Rexroth — это инновационное оборудование, предназначенное для оптимизации работы гидравлических систем и обеспечения более эффективного использования энергии. Баллонный аккумулятор HAB2 выполняет несколько важных функций. Во-первых, с..

24 Ноября, 2023
Bosch Rexroth: инновационное решение для удобства и эффективности работы - выдвижная клавиатура VAK40 

Торговая марка Bosch Rexroth, является одним из мировых лидеров в области промышленной автоматизации, и представляет свою разработку - выдвижную клавиатуру VAK40. Это инновационное устройство, которое обеспечивает удобную и эффективную работу операторов в промышленных условиях. Установить выдви..

23 Ноября, 2023
Bosch Rexroth: инновационные функции и простая установка дисплея 19" VDP60

Бренд Bosch Rexroth рад представить свою разработку - дисплей 19" VDP60, который обещает стать настоящим прорывом в мире технологий. Этот дисплей не только показывает изображения высокого качества, но и предлагает ряд функций, которые помогут решить множество задач. Одним из главных свойст..

22 Ноября, 2023
Rexroth: Шестеренные насосы с внешним зацеплением – надежное решение для эффективной работы в различных отраслях

Компания Rexroth представляет шестеренные насосы с внешним зацеплением, которые являются необходимым прибором в области гидравлики. Они выполняют важную задачу – обеспечивают надежную и эффективную работу гидравлических систем в различных отраслях промышленности. Эти насосы нашли применен..

21 Ноября, 2023

Нет отзывов об этом товаре.

Написать отзыв

Рейтинг